Two parallel plates kept 295mm a part have laminar flow of oil . The lower plate is stationary and the upper plate is moving with 4.75m/s . find: a- velocity distribution formula. b- The value and position of the maximum velocity.c- The discharge per meter width. d- The shear stress at the plates. e- The difference in pressure between two points 50m apart. f- The velocity gradient at the plates. g- The velocity at 130 mm. Assume viscosity of oil to be 24.5 poise.

Two parallel plates kept 295mm a part have laminar flow of oil . The lower plate is stationary and the upper plate is moving with 4.75m/s . find: a- velocity distribution formula. b- The value and position of the maximum velocity.c- The discharge per meter width. d- The shear stress at the plates. e- The difference in pressure between two points 50m apart. f- The velocity gradient at the plates. g- The velocity at 130 mm. Assume viscosity of oil to be 24.5 poise.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

SHEAR STRESS 2 If the T-beam is subjected to a vertical shear of V = 60 kN, determine the maximum shear stress in the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch the variation of the shear-stress intensity over the entire cross section. VQ TRỊ = It 100 mm (60 kN)Q 100 mm 75 mm 100 mm I(300) B' VQ TB = VQ 150 mm It I(100) A V = 60 kN
SHEAR STRESS 2 If the T-beam is subjected to a vertical shear of V = 60 kN, determine the maximum shear stress in the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch the variation of the shear-stress intensity over the entire cross section. VQ TBI = It (60 kN)Q 100 mm 100 mm 75 mm 100 mm I(300) B' VQ TR = It VQ B 150 mm I(100) V = 60 kN
CLO 1: Determine the maximum tensile stress in MPa if P = 115 %3D kN. 20 mm 25 mm 20 mm 45mm 3somm 16.064 28.395 45.176 10.040 46 mm
13. The velocity distribution over a plate is given by u= y-y in which u is the velocity in m/sec at a distance of y m above the plate. Determine the shear stress at y 0, 0.1 and 0.2 m. Take u = 6 poise. [Ans. 0.4, 0.028 and 0.159 N/m)
PROBLEM 6 The rigid bar DC below is horizontal under no load, and bars A and B are unstressed. When the load P is applied, the strain in bar B is found to be 0.0015. Determine (a) the factor of safety with respect to failure by slip for bar A. (b) The load P (c) The vertical displacement (deflection) of point C. E B A C 100 mm 100 mm 50 P. 200 mm 375m m
The T section is shown in Figure below is the cross-section of a beam. The beam is subjected to a uniform distributed load = 4 kN/m. The N.A is located at 34.7 mm from the bottom and that IxA =10.64x106 mm. Determine (a) the maximum shearing suess (b) the shearing stress at 15 mm from the bottom face. Q2 %3D 20mm 4 kN/m 120mm A 34.7 mm 20mm lm 3m 1m 220mm TT
Consider the beam shown in the figure. a. Determine the Maximum Tensile Flexural Stress. b. Determine the Maximum Vertical Shear Stress. 20KN/m ↓ ↓ ↓ 2M ↑ Com 200mm 200m ↓ 기 200mm 2m ] [ 20AM
0/5 find the normal stress at left of point 1) A 100 B C D 40 kN 50 kN 40 mm 70 10 KN (1) 20 mm 30 mm 100 mm 300 mm 300 mm 200mm 21.3 MPa 23.8 MPa 26.4 MPa O no one
What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object? The shearing stress value will be The angle of twist will be
A 40-mm-diameter solid shaft is subjected to an axial force of P= 2480 N, a vertical force of V= 1880O N, and a concentrated torque of T= 66 N-m, acting in the directions shown. Assume L- 130 mm. Determine the normal stress o, at point H. %3D H T. O 29.3 MPa 44.7 MPa O 40.9 MPa О 34.7 МРа O 55.9 MPa eTextbook and Media
1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m
An oil (M = 0.083 N.Sec/m) Flows belween tWe inclined PiXed and Parallel Plates (a= 24 mm) If the averaje Velocit y equals (o-1S m/Sec) distance %3D Calculate the Shear Stress at (m m and 12mm from the lower Plate Us ing V = to Solved . 24 mm