SHEAR STRESS 2 If the T-beam is subjected to a vertical shear of V = 60 kN, determine the maximum shear stress in the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch the variation of the shear-stress intensity over the entire cross section. VQ TRỊ = It 100 mm (60 kN)Q 100 mm 75 mm 100 mm I(300) B' VQ TB = VQ 150 mm It I(100) V = 60 kN

SHEAR STRESS 2 If the T-beam is subjected to a vertical shear of V = 60 kN, determine the maximum shear stress in the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch the variation of the shear-stress intensity over the entire cross section. VQ TRỊ = It 100 mm (60 kN)Q 100 mm 75 mm 100 mm I(300) B' VQ TB = VQ 150 mm It I(100) V = 60 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the following data: Cross section: 50mm x 75mm P = 200 kN e 15 with the x-axis a. Find the tensile stress (in MPa) on plane A-A. b. Find the shear stress (in MPa) on plane A-A. c. Find the angle (in degrees) of plane A-A in which the shear stress is maximum.
SE a iir Draw the V and M diagram of the beam. The cross section of the beam is a triangle with base 18 and height 12mm. Calculate the maximum shear stress in the beam. 5m 18mm D 1000N/m 12mm 2m B 1m 2m C A
10-7. The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in the shaft and sketch the shear-stress distribution along a radial line of the shaft where the shear stress is maximum. Set T₁ = 2000 N. m. E D 300 N-m 600 N-m T₁ Probs. 10-6/7 B 900 N-m
Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm Y-face 50 X-face D= 40 mm. 30MN m2 30 50 MN m-
4Iven: Ex : -533 x10 Ex: -533 x/0-6 67x10-6 Yx, = -l626 x /0-b E : 30 x/0 psi Y: ,30 Find: Stress Components on face +45° from X -axis.
An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t Y ▼ 2 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response: 318.329 mm 290.593 mm 355.903 mm 263.312 mm
Given: Four-25-mm-diameter rivets with an axial load of T= 75 kN distributed equally as shown. The thickness of the plates is 25 mm and width of plate is 150 mm. find (a) the shear stress on the rivets (b) the bearing stress between a plate and a rivet; (c) the minimum average tensile stress in each plate. ft T T
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
11-95. The beam has the rectangular cross section shown. If w = 1 kN/m, determine the maximum bending stress in the beam. Sketch the stress distribution acting over the cross section. %3D 50 mm I 150 mm -2 m- -2 m- -2 m Probs. 11-94/95
3:30 51 Photo Done Problem 1: A round solid shaft is subjected to torsion as shown. Find: 1- Maximum torsional shear stress of the steel and aluminum shafts. 2-Angle of twist at point C. Steel G = 30.0x106 psi 3" Radius Steel 2" Radius Aluminum π/ DA Aluminum G = 15.0x105 psi A B T₁ = 50 k-ft T₂ = 20 k-ft 8 ft 12 ft + T2 +
PROBLEM 6 The rigid bar DC below is horizontal under no load, and bars A and B are unstressed. When the load P is applied, the strain in bar B is found to be 0.0015. Determine (a) the factor of safety with respect to failure by slip for bar A. (b) The load P (c) The vertical displacement (deflection) of point C. E B A C 100 mm 100 mm 50 P. 200 mm 375m m
Detemine the principal stress acting at point B, which is located just on the web, below the horizontal segment on the cross section Show the results on a properly oriented element located at this point. Although it is not very accurate, use the shear formula to calculate the shear stress. -AO mm- 300 mm 150 mm 12 mm 130 mim 15 mm 6 kN