Two components A and B, with specification below: 1. Component A: 10 kW active power (P), 30 KVAR reactive power (Q), lagging 2. Component B: 50 kVA complex power (S), with 0.4 power factor, leading Draw the power triangle of : 1. Component A 2. Component B 3. Component A and B, parallel to each other in a circuit Please note, each power triangle must contains a value of P, S, Q, and the phase of voltage relative to current (0)

Two components A and B, with specification below: 1. Component A: 10 kW active power (P), 30 KVAR reactive power (Q), lagging 2. Component B: 50 kVA complex power (S), with 0.4 power factor, leading Draw the power triangle of : 1. Component A 2. Component B 3. Component A and B, parallel to each other in a circuit Please note, each power triangle must contains a value of P, S, Q, and the phase of voltage relative to current (0)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. What is the minimum AC voltage rating of each capacitor? Answer is 1200 volts. What is the current flow through the circuit? And what is the minimum kVAR rating of each capacitor?
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power is O 4000 VA O 8000 VA O 6000 VA O 2000 VA
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power Is O 4000 VA CO 8000 VA O 6000 VÀ O 2000 VA
Draw three transformers for each of the different three-phase connections. That is, draw three transformers and then make the connection, eg star-star, then redraw three transformers and make another three-phase connection, and so on until all four combinations of three-phase connections are made.
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
An 11 kV generating station has four identical 3-phase alternatorsGl, G2, G3 and G4 each of L0 MVA capacity and l2%o reaclarce.There are two section of bus-bar P and Q, linked by a reactor X ratedat 10 MVA with 24o/oreactance. From section Q load is taken througha 6 MVA, i 1kV/66kV step-up transformer (T1) having a reactance of37o. Determine the fault current if a three-phase short-circuit occursnear the high voltage terminal of the transformer (F) as shown inFigure.Assume prefault voltages to be 1 pu and prefault currents to be zero
A power supply A delivers 10 V dc with a ripple of 0.5 V r.m.s. while the power supply B delivers 25 V dc with a ripple of 1 mV r.m.s. Which is better power supply ?