A balanced, three-wire, Delta-connected, three-phase load has a phase voltage of 261.7 V, a line current of 3.9 A and unity power factor. Determine the total active power delivered to the load. O A. 1767.73 W O B. 3061.89 W O C. 116.22 W O D. 1020.63 W

A balanced, three-wire, Delta-connected, three-phase load has a phase voltage of 261.7 V, a line current of 3.9 A and unity power factor. Determine the total active power delivered to the load. O A. 1767.73 W O B. 3061.89 W O C. 116.22 W O D. 1020.63 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Determine the amplitude of the line current in a three-phase system with a line voltage of 207 V…

Q: A load of 40 -j 30 is connected to a source of 100 V with a phase angle of 300, through a…

A: Reactive power- Reactive power is the part of complex power that corresponds to storage and…

Q: A balanced three-phase source supplies a balanced delta load having 39 angle -40° Q per phase. The…

A: The solution is given below

Q: 7. Three parallel three phase loads, wye connected are supplied from 208 Vrms, 60 Hz three phase…

A: The solution is given below

Q: A balanced three-phase star-connected R-C load of 145 kW takes a current of {I} A with a line…

A: Given, P=145 kWVL=900 Vf=50 HzCurrent =I AIL=Iph=I A

Q: For the circuit shown below, all the voltage values are given in rms. The apparent power of the…

A: The given circuit is: All voltages values are given in RMS. Apparent power of three phase load,…

Q: 14. A wye-connected balanced three-phase load draws 75 A from 230 V, 60 Hz, source. To measure the…

A: From the question, it is given that per phase load current of 75 amps . Also, it is given that…

Q: .A balanced 40 Ohms Y-connected load is connected to a 480V (line voltage), three phase source. Find…

A: A balanced 40 Ohms Y-connected load is connected to a 480V (line voltage), three phase source. To…

Q: 5. It is required to raise the power factor of a 750 kW balanced 3-phase load from 0.70 lagging to…

Q: if V = 120 < 30 Vrms, S= 23 - j 17.3 VA, 1)the value of the power factor is?/2) the value of the…

Q: Determine phase impedances of a wye-connected balanced three-phase load 20 kVA, 400 V at PF=0.866…

A: According to question:…

Q: A balanced three-phase source furnishes power to the following three loads: Load 1: 6 kVA at 0.83…

Q: In the network below, EA = 23020° V and the phase sequence is acb. Two wattmeters are used to…

Q: A load connected in star, with impedances of 24 ≮ 20°, has a voltage Vac = 208 ≮ 10°, Calculate: a-…

A: In this question, We need to determine the phase current, phase voltage and line voltage? Assume…

Q: A balanced wye-connected load has a phase impedance of 15 + j10 ohms. What is the impedance per…

A: Given: Balanced wye-connected load phase impedance, ZY=15+j10 Ω

Q: A 3-phase system has line to line voltage Vab = 1500 Vrms with 30 deg angle with a wye load.…

A: For star load line voltage is sq rt(3) times of phase voltage and leads by angle of 30 degree

Q: A balance Y-connected load of ( 3 + j8 ) ohms per phase is supplied by a balanced three- phase, 60…

A: The solution is given below.

Q: A three-phase power source delivers a power of 12KVA at a lagging power factor of 0.8 to a…

Q: Assume that the phase-voltage magnitudes for a wye system are 100V. Find the magnitude of the…

Q: Given ??? = 208 ∠ − 40° V in a three-phase ACB circuit, find the currents of the phasor line for a…

A: Given, a three-phase ACB circuit having Line voltage, VL = 208 ∠ − 40° V Active power, P = 10 kW…

Q: 1. A balanced wye connected load absorbs a total power of 5 kW at a leading p.f. of 0.6 when…

A: In this question we need to find a load impedance

Q: Why is the wye to wye connection have both the phase voltage and the line-to-line voltage the same…

A: Wye is the connection method for a three-phase circuit in which all the three loads are connected…

Q: Determine the amplitude of the line current in a three-phase system with a line voltage of 300 V…

A: In a three-phase system there are two ways to connect a three phase load. Star/Wye Connection Delta…

Q: A balanced wye-connected system has a phase voltage of 200V RMS and impedance of 1000L20°. Calculate…

Q: 4. A balanced wye-connected, three-phase load withdraws 150 A per phase with a leading power factor…

A: The solution is given below

Q: 4. A single phase load draws a current of 30 / 35 deg A. The voltage across the load is 220/ 75 deg…

Q: A balanced Delta- connected load of (8+j6) Q per phase is supplied from a 3-phase 440 V source. Find…

A: Given load/phase=8+j6Vsline=440VLine current=3×Vs2=3×4408+j6Iline=76.21∠-36.86° APower…

Q: A balanced three-phase star-connected R-C load of 120 kW takes a current of 60 A with a line voltage…

Q: lanced three-phase source with grounded neutral has line-to-line voltages of 208 volts with ab-bc-ca…

A: In this question, A balanced three-phase source with grounded neutral line-to-line voltagesVLL =…

Q: Find the total real power dissipation in a balanced delta-connected system. Phase voltage is 100V…

A: Given: A balanced delta connected system Phase voltage, Vph=100 V Load impedance, Zph=175 Ω Power…

Q: A balanced wye-connected load absorbs a total power of 2 kW at a leading power factor of 0.9 when…

A: Wye-Connected Load: The Wye-Connected Load block represents a wye-connected three-phase load. Any…

Q: If a balanced 3-phase system has its phase voltage Van = 120440°, then the line-to-line voltage Vpc…

Q: = 7200 ∠ - 130 ° V VBN = 7200∠110 ° V? Also, find VCN

A: The sequence components are equal in magnitude and displaced by 120 degree. The angle between the…

Q: The total real power absorbed by a balanced three-phase delta-connected load is 34 kW. The power…

A: Given: A three phase delta connected load with, P=34 kWcosθ=0.87VL=365 V

Q: A balanced three-phase source furnishes power to the following three loads: Load 1: 6 kVA at 0.83 pf…

Q: In the circuit below, the voltage between phase is 230Vrms. Find the phase current, line current, P,…

A: As per the guidelines of Bartleby we supposed to answer first three sub part of the question for…

Q: 3. The power factor of each phase of a balanced wye-connected 5-ohm impedance is 0.6 lagging. This…

Q: A balanced three-phase load requires 330 kW at a lagging power factor of 0.9. The load is fed from a…

A: sending end power factor = cos (arctan(sending end reactive power / sending end active power)…

Q: A balanced three-phase A-connected load with a phase impedance of 10-j16 Q. If the line voltage is…

A: A balanced system where all the connected load across voltage are equal . In balanced three phase…

Q: balanced wye-connected system has a phase voltage of 200V RMS and impedance of 1000420'. Calculate…

Q: A three-phase power source delivers a power of 30KVA at a lagging power factor of 0.6 to a…

A: The circuit this is excited the use of alternating supply is referred to as an AC Circuit. The…

Q: Group B Q1/ A balanced acb-sequence A-connected source with a voltage of 100 V, is connected to a…

Q: 4. A single phase load draws a current of 30 / 35 deg A. The voltage across the load is 220 / 75 deg…

Q: A balanced 3-phase, star connected load of 120 kW takes a leading current of 100A with a line…

A: Given, A balanced 3-phase star connected load with, Load power, PL=120 kW Leading current,…

Q: AC CIRCU.. 19. A three-phase, three-wire, 240 V CBA system supplies power to a wye-connected load…

A: The solution is given below

Q: 22 10+js 8+j6 125 I, For the circuit shown below, Take Van = 100 Vrms and the transmission line…

A: Given

Q: A balanced three-phase star-connected R-C load of 120 kW takes a current of 90 A with a line voltage…

Q: A balanced three-phase star-connected R-C load of 140 kW takes a current of 72A with a line voltage…

A: Power =3×VL×IL ×cosθ. From above relation we will find power factor. impedance=Per phase voltageper…

Q: Example 5.1: A Circuit draws a 200 V and its pf is 0-8 lagging. Active Power, and Reactive Pow…

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

A balanced, three-wire, Delta-connected, three-phase load has a phase voltage of 261.7 V, a line current of 3.9 A and unity power
factor. Determine the total active power delivered to the load.
O A. 1767.73 W
O B. 3061.89 W
O C. 116.22 W
O D. 1020.63 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In case RL load, it is desired to get an average load voltage of 75 V. Determine the firing angle if the ac supply voltage is 200V per phase. If the load resistance is 302, calculate the average load current and power. Design the thyristor. 4-
A voltage and current applied to a single phase load is v= 26 cos (300t+35) and i= 19 cos (250t- 20). Find the single and three phase active and reactive power of the circuit if the voltage and current are in sine waveform
Determine the apparent power, active power and reactive power in a series circuit, when the supply voltage is 75 Volt, the current is 1 Amp and the phase angle is 30 lagging. Also, draw a power triangle for the circuit.
Three identical impedances are connected in star across a 440 V, 3 phase, 50 Hz supply. The line current is 40 A and the pf is 0.8 leading. Find the value of resistance and capacitance in each phase.
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
1) Two identical voltage waveforms of difference phase angles are shown in Figure B. Write down the expression of waveforms A and B clearly. HUS Voltage (V) 8 0 K/N B 7: ST ot
Use 3 decimal places and box the final answer. A 4-ohm resistor is in series with a 7.96-mH inductor connected across a 110-V 60-Hz source. Determine : a) the impedance b) the input current c) the voltage across the resistor and the inductor d) Draw the phasor diagram showing the current and the voltages. e) The power factor and the power input to the circuit.
6. Determine the peak and average power delivered to RL in figure. 2:1 RL 220 N 120 V rms alll lelll
The complex volt amperes in a series circuit are (4300- j2500) and the current is (25 + j43.3)A.Find the applied voltage.
5) The power was taken by a C–R series circuit, when connected to a 105V, 2.5 kHz supply, is 0.9kW and the current is 15A. Calculate (a) the resistance, (b) the impedance, (c) the reactance, (d) the capacitance, (e) the power factor, and (f) the phase angle between voltage and current.
Predict the output when the input three phase signal is given to the circuit shown in figure.3. IA D1 Va A IpC IB D2 VB 3-phase 4-wire VDC ROAD AC Supply Ic D3 Vc Vphase N Figure.3
A voltage and current applied to a single phase load is v= 25 sin (300t+30) and i= 16 sin (250t- 40"). Find the single and three phase active and reactive power of the circuit if the voltage and current are in cosine waveform.