The large piston of a hydraulic lift had a cross-sectional area 60 times mc ross-sectional area. Determine the force F2. Instruction: Type your answer without any unit. Type only the number) F1 = 20 N Small Piston, A1 L arge Piston An

The large piston of a hydraulic lift had a cross-sectional area 60 times mc ross-sectional area. Determine the force F2. Instruction: Type your answer without any unit. Type only the number) F1 = 20 N Small Piston, A1 L arge Piston An

Name: The large piston of a hydraulic lift had a cross-sectional area 60 ti
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: The large piston of a hydraulic lift had a cross-sectional area 60 times more than the smallcross-sectional area. Determine the force F2.(Instruction: Type your answer without any unit. Type only the number)F1= 20 NSmall Piston, A1Large Piston, A2F2

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter12: Fluid Dynamics And Its Biological And Medical Applications

Section: Chapter Questions

Problem 7PE: (a) As blood passes through the capillary bed in an organ, the capillaries join to form venules...

See similar textbooks

Similar questions

What is the difference between flow rate and fluid velocity? How are they related?
What fraction of an iceberg floating in the ocean is above sea level? Assume the density of the iceberg is 917 kg/m3.
Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
How much pressure is transmitted in the hydraulic system considered in Example 11.6? Express your answer in pascals and in atmospheres.
(a) Using Bernoulli's equation, show that be measured fluid speed v for a pitot tube, like the one in figure 14.32(b), is given by v=( 2gh)1/h , where h is be height of be manometer fluid, p' is the density of the manometer fluid, p is the density of the moving fluid, and g is be acceleration due to gravity. (Note that v is indeed proportional to the square root of h, as stated in text) (b) Calculate v for moving air if a mercury manometer's h is 0.200 m. Figure 14.32 Measurement of fluid speed on Bernoulli’s principle. (a) A manometer is connected to two tubes close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, so the fluid has a speed v across; thus, pressure there drops. The difference in pressure at the manometer is 12v22 , so h is proportional to . 12v22 (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.
Pascal’s Principle and Hydraulics 59. How much pressure is transmitted in the hydraulic system considered in Example 14.3? Express your answer in atmospheres.
A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.
(a) As blood passes through the capillary bed in an organ, the capillaries join to form venules (small veins). If the blood speed increases by a factor of 4.00 and the total cross-sectional area of the venules is 10.0 cm2, what is the total cross-sectional area of the capillaries feeding these venules? (b) How many capillaries are involved if their average diameter is 10.0 m?
Gauge pressure in the fluid surrounding an infant's brain may rise as high as 85.0 mm Hg (5 to 12 mm Hg is normal), creating an outward force large enough to make the skull grow abnormally large. (a) Calculate this outward force in newtons on each side of an infant's skull if the effective area of each side is 70.0 cm2. (b) What is the net force acting on the skull?
Figure 11.35(a) shows the effect of tube radius on the height to which capillary action can raise a fluid. (a) Calculate the height h for water in a glass tube with a radius of 0.900 cm—a rather large tube like the one on the left. (b) What is the radius of the glass tube on the right if it raises water to 4.00 cm?
Archimedes' principle can be used to calculate the density of a fluid as well as that of a solid. Suppose a chunk of iron with a mass of 390.0 g in air is found to have an apparent mass of 350.5 g when completely submerged in an unknown liquid. (a) What mass of fluid does the iron displace? (b) What is the volume of iron, using its density as given Table 14.1? (c) Calculate the fluid's density and identify it.
The hydraulic system of a backhoe is used to lift a load as shown in Figure 11.45. (a) Calculate the force F the slave cylinder must exert to support the 400-kg load and the 150-kg brace and shovel. (b) What is the pressure in the hydraulic fluid if the slave cylinder is 2.50 cm in diameter? (c) What force would you have to exert on a lever with a mechanical advantage of 5.00 acting on a master cylinder 0.800 cm in diameter to create this pressure? Figure 11.45 Hydraulic and mechanical lever systems are used in heavy machinery such as this back hoe.