A force of 470N is exerted on the pedal cylinder of an automatic hydraulic system. The pedal cylinder has a diameter of 0.425 cm. How much pressure is transmitted in the hydraulic system? Express your answer in atmospheres. atm

A force of 470N is exerted on the pedal cylinder of an automatic hydraulic system. The pedal cylinder has a diameter of 0.425 cm. How much pressure is transmitted in the hydraulic system? Express your answer in atmospheres. atm

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 14.75AP

See similar textbooks

Related questions

Q: The piston of a hydraulic automobile lift is 0.30 mm in diameter. Part A What gauge…

A: diameter (d) = 0.3 mMass of car (m) = 1200 kg

Q: In the hydraulic press used in a trash compactor, the radii of the input piston and the output…

A: Given,

Q: What is the pressure at a depth of 90 m in the ocean? The density of seawater is 1. 03 × 10 3kg/m3.…

Q: The maximum gauge pressure in a hydraulic lift is 16.9 atm . 1 atm = 1.013 × 105 N/m². Part A What…

A: Given data The pressure in atm is given as P = 16.9 atm. 1 atm = 1.013 x 105 N/m2. The diameter of…

Q: The diameters of the large and small cylinders of a hydraulic press are 2.4 cm and 48.0 cm,…

A: As per Pascal’s law, the pressure on both the cylinder of the hydraulic press is the same, thus,…

Q: A hydraulic system has two pistons of different diameter and uses a liquid of density p=1260 kg/m3.…

A: pressure on side of smaller piston = F1/A1 = (1.3*9.8)/π(0.01)2 = 40552.68 Pascalspressure on side…

Q: Two pistons of a hydraulic lift have a radius of 5 cm and 11.5 cm respectively. If the input force…

A: Radius R1= 5 cm R2 = 11.5 cm Force on small piston (F1) = 500N

Q: same as the work output, assuming no losses to friction. What must be the ratio of the distance the…

Q: Find the pressure in the water at the base of a dam if the water in the reservoir is 300 meters…

Q: What is the pressure at a depth of 110 m in the ocean? The density of seawater is 1. 03 x 10 kg/m.…

Q: The drawing shows an intravenous feeding. With the distance shown, nutrient solution (p = 1050 kg/m)…

A: The pressure due to the fluid is given by P = h d g where, h is the height of the fluid, d is the…

Q: A force of F1 = 394 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0191 m.…

Q: In a simple hydraulic system piston 1 has a cross section area of 0.00050 m2 , and piston 2 has a…

Q: The following figure shows the shape and dimensions of a small dam. Assuming the water level is at…

A: The force acting on the face of the dam can be given by, F=mg...........(1) where, F= force…

Q: A water pipe having a 2.05 cm inside diameter carries water into the basement of a house at a speed…

Q: A hydraulic car lift has an input piston of radius 8.7 cm and negligible weight. The output piston…

Q: A horizontal pipe of diameter d1 = 12 cm carrying water has a constriction of diameter d2 = 6 cm. If…

A: We have from Bernoullis equation P1+12ρv12=P2+12ρv22 And the continuity equation A1v1=A2v2 So we get…

Q: A water pipe having a 2.45 cm inside diameter carries water into the basement of a house at a speed…

Q: 17.Consider the following situations: In an automotive shop, the force exerted on the small piston…

Q: The cross-section area of Piston A1 is 0.000400m2 The cross-section area of Piston A2 is 0.000800m2…

A: Given data: Cross-section area of Piston 1 (A1) = 0.000400 m2 Cross-section area of Piston 2 (A2) =…

Q: The drawing shows a hydraulic chamber with a spring (spring constant = 1190 N/m) attached to the…

Q: A hydraulic lift raises a 1446 kg automobile when a 677 N force is applied to the smaller piston. If…

Q: A force of 343 N is applied to a hydraulic jack piston that is 0.0388 m in diameter. The second…

Q: In a simple hydraulic system piston 1 has a cross section area of 0.000050 m2 , and piston 2 has a…

A: Given data: The cross-section area of the piston 1 is A1=0.000050 m2 The cross-section area of the…

Q: In the hydraulic press used in a trash compactor, the radii of the input piston and the output…

Q: The diameters of the large and small cylinders of a hydraulic press are 2.4 cm and 48.0 cm,…

A: Given Diameters of the large and small cylinders of a hydraulic press are d1= 2.4 cm and d2= 48.0…

Q: A force of 295 N is applied to a hydraulic jack piston that is 0.026 m in diameter. The second…

A: GivenF1 = 295 Nd1 = 0.026 md2 = 0.19 m

Q: Awater pipe having a 2.84 cm inside diameter carries water into the basement of a house at a speed…

Q: A very simple way of measuring the depth of a fluid in a gas station's underground gasoline tank is…

A: Given that The density of the gasoline is (ρ) = 700kg/m3 The…

Q: A force of F1 = 374 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0192 m.…

Q: A force of F1 = 397 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0183 m.…

A: In this question we have to find the magnitude of the output force F2. Please give positive feedback…

Q: A water pipe having a 2.34 cm inside diameter carries water into the basement of a house at a speed…

A: This question is based on Mechanical Properties of fluids topic. Bernoulli's Principle states that…

Q: A water pipe having a 2.36 cm inside diameter carries water into the basement of a house at a speed…

Q: In a simple hydraulic system piston 1 has a cross section area of 0.000050 m2 , and piston 2 has a…

A: Given: The cross-section area of piston 1 is 0.00005 m2. The cross-section area of piston 2 is…

Q: A water pipe having a 2.34 cm inside diameter carries water into the basement of a house at a speed…

Q: Pressure in the spinal fluid is measured. If the pressure in the spinal fluid is 10.0 mm Hg: (a)…

A: P0=Pressure in the spinal fluid=10 mm Hgρ=Density of fluid=1.05 g/mL=1.05×103 kg/m3g=Acceleration…

Q: A hydraulic piston has two surfaces which can move when a force is applied to them. On the left…

A: a)The total force on the right side will be,

Q: The gauge pressure at the bottom of a cylinder of liquid is pg = 0.40 atm. The liquid is poured into…

A: Given data The gauge pressure at the bottom of the first cylinder of liquid is: pg = 0.40 atm The…

Q: Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on…

A: Given: P = 80 kPa d (mercury) = 13600 kg/m3 d (water) = 1000 kg/m3

Q: What is the radius of the pipe on the second floor

Q: A water pipe having a 2.47 cm inside diameter carries water into the basement of a house at a speed…

A: a) Apply the continuity equation to determine the velocity at the second floor.

Q: What is the pressure at a depth of 150 m in the ocean? The density of seawater is 1. 03 × 10…

A: The pressure at the depth is given by, P=P0+ρgh Here, P0 is the atmospheric pressure, ρ is the…

Q: A hydraulic jack has an input piston of area 0.0560 m2 and an output piston of area 0.750 m2. How…

A: input area, a = 0.056 m2 output area, A = 0.75 m2 Output force, F = 1.4 x 104 N

Q: What is the flow rate of water (in m3/s) hose that can fill 1.75 L bottle in 5 seconds? Group of…

A: Given, Volume of water = 1.75 L = 1.75×10-3 m3 Time = 5s Flow rate = Volume filledTime taken

Q: The small piston of a hydraulic lift (see figure below) has a radius of r1= 1.00 cm, and its large…

A: Please see the answer in step 2

Q: A force of 100 N is applied to the brake pedal, which acts on the cylinder—called the master—through…

A: The transmitted pressure in the hydraulic system is,

Question

100%

A force of 470 N is exerted on the pedal cylinder of an automatic hydraulic system. The pedal cylinder has a diameter of 0.425 cm. How much pressure is transmitted in the hydraulic system? Express your answer in
atmospheres.
atm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

(a) Verify that work input equals work output for a hydraulic system assuming no losses to friction. Do this by showing that the distance the output force moves is reduced by the same factor that the output force is increased. Assume the volume of the fluid is constant. (b) What effect would friction within the fluid and between components in the system have on the output force? How would this depend on whether or not the fluid is moving?
You are pumping up a bicycle tire with a hand pump, the piston of which has a 2.00-cm radius. (a) What force in newtons must you exert to create a pressure of 6.90105 Pa (b) What is unreasonable about this (a) result? (c) Which premises are unreasonable or inconsistent?
(a) How high will water rise in a glass capillary tube with a 0.500-mm radius? (b) How much gravitational potential energy does the water gain? (c) Discuss possible sources of this energy.
The left ventricle of a resting adult's heart pumps blood at a flow rate of 83.0 cm3/s , increasing its pressure by 110 mm Hg, its speed from zero to 30.0 cm/s, and its height by 5.00 cm. (All cumbers are averaged over the entire heartbeat) Calculate the total power output of left ventricle. Note that most of the power is used to increase blood pressure.
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
(a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
What is the difference between flow rate and fluid velocity? How are they related?
The human circulation system has approximately 1109 capillary vessels. Each vessel has a diameter of about 8 m. Assuming cardiac output is 5 L/min, determine the average velocity of blood flow through each capillary vessel.
Review. The tank in Figure P15.13 is filled with water of depth d. At the bottom of one sidewall is a rectangular hatch of height h and width w that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by die water about die hinges.
Review. The tank in Figure P15.13 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 m that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by the water about the hinges.
An airplane is cruising at altitude 10 km. The pressure outside the craft is 0.287 atm; within the passenger compartment, the pressure is 1.00 atm and the temperature is 20C. A small leak occurs in one of the window seals in the passenger compartment. Model the air as an ideal fluid to estimate the speed of the airstream flowing through the leak.
(a) Estimate the time it would take to fill a private swimming pool with a capacity of 80,000 L using a garden hose delivering 60 L/min. (b) How long would it take to fill if you could divert a moderate size river, flowing at 5000 m3/s, into it?