The following equation was suggested both for cache memory and disk cache memory Ts = Tc + M * Tp %3D Generally this equation to a memory hierarch' with N levels instead of just two levels.
Q: e system shown below, answer following questions CLK 3.3GHZ DATA BUS (16 bits) CPU ADDRESS BUS (23…
A: 1). 2address bus width Equals total addressable memory * The size of the data bus. For example, a…
Q: Section 5.5 states that modern server memory modules (DIMMs) employ SEC/DED ECC to protect each 64…
A: Given data: A single error correcting, double error detecting(SEC/DED) hamming code is present and…
Q: a. How many bits are required to address a 32M x 32 memory if: Main memory is byte addressable? 2^20…
A:
Q: For a memory with a 5bit wide address bus and a 32bit wide data bus, answer the followin uestions:…
A: A) Total number of distinct address = 2 address bus width = 25 = 32
Q: where R1, R2, and R3 are CPU registers, (R1) is the content of R1, a, ß,7, and are the starting…
A: We have , For each operations of given instruction code segment has number of instructions are:-…
Q: Answer the following questions. A. A computer system has a main memory access time as 60ns. you as a…
A: ANSWER:-
Q: 3) Assume SS=5000H, DS=600OH, ES=7000H, CS=9000H, BX=1000H, DI=2000H, SP=3000H, IP=4000H, SI=2000H,…
A: Given Instruction: MOV [DI + 3000H], AL. -> Here MOV means Move instruction. The content of…
Q: Q1. Suppose you are given with a ROM chip of size 1024*8 and 5 RAM chips of size 512*8. Show…
A: Answer: I have given answered in the handwritten format in brief explanation
Q: 3- Suppose that DS = 100H, SS = 300H, BP = 200H, and SI = 0100H, BX= 1500H . Determine the memory…
A: DATA Given:- DS=100H SS=300H SI=0100H BX=1500H Instruction : MOV DL,[BP+200] Operation : Real…
Q: How many bits are required to address a 8M × 16 main memory if a) Main memory is…
A: How many bits are required to address a 8M × 16 main memory if a) Main memory is…
Q: 1 Problem: Draw the complete diagram of a 256KX8 memory that uses RAM chips with the following…
A: Total # of 32Kx4 RAM Chips required = 256Kx8 / 32Kx4 = 8x2 = 16 These 16 chips will be arranged as 8…
Q: 2. Consider 2M x 8 SRAM memory block. (a) How many bits of data can be stored in this memory block?…
A: Disclaimer: “Since you have asked multipart questions, As per our company policy,we will only solve…
Q: 8.3 An Acc-ISA CPU executes the following instructions using 3-bit op-codes and 5-bit address or 2's…
A: Here is the answer:-
Q: Consider cache memory 90% hit ratio is required to be installed in a memory system to reduce the…
A: Given, Hit ratio = 90 % Then, Hit rate = 0.9 Miss rate = 1 - hit rate = 1 - 0.9 = 0.1 According to…
Q: 2. What is the resulting memory address for the following operands assuming the indicated values in…
A: Basics: A memory address is a reference to a particular memory area utilized at different levels by…
Q: The purpose of memory hierarchy is To reduce memory cost per bit To reduce average memory access…
A: We have memory hierarchy like Cache level 1 and then cache level 2 then main memory and finally…
Q: Can the virtual addresses 0x100000 and 0x100008 be mapped to 2 far apart locations in physical RAM?…
A: Answer is No
Q: 2-Suppose that DS = 100H, SS = 2000H, BP = 200H, and SI = 0100H, BX= 1500H. Determine the memory…
A: Solution Given , DS=100H SS=2000H BP=200H SI=0100H BX=1500H Instruction is : MOV AL , [ BX + 500 ]
Q: Assume, paging has been used as memory management technique and the page table is stored in memory…
A: Assume, paging has been used as memory management technique and the page table is stored in memory…
Q: For a system, RAM - 64KB, Block size - 4 bytes, Cache size - 128 bytes, Direct mapped cache.…
A: Given: RAM size = 64 KB Block size = 4 bytes Cache size = 128 bytes
Q: Following is the memory map begining from addre= ACOOH and increasing addresses to the right, all in…
A: It is defined as a unique identifier used by a device or CPU for data tracking. This binary address…
Q: 2. Design your own 16 bits Memory Map, and choose the amount of memory space required for various…
A: 16bit processor,16bit(word-sized), can address 64k of RAM. 220(1048576)bytes, so can construct 20bit…
Q: Why do we need cache memory when we already have RAM (Random Access Memory), which is a kind of…
A: Cache Memory: Data retrieval from the a computer's memory is made more effective by cache memory, a…
Q: What is the idea of Memory Segmentation ? O Having multiple base and bounds pair per CPU in the MMU.…
A: Here, we have to provide correct option for Memory segmentation.
Q: 12. Consider the following instruction: Instruction: AND Rd,Rs,Rt Interpretation: Reg[Rd] = Reg[Rs]…
A: The question is on choosing the correct option from the given options considering the given…
Q: Please solution with explain ЗFFE Question 1 A memory map shown in Fig-1 with the addresses of…
A: Question 1: Part A) Base address of EAROM=1000 (in hex) Number of location =2592=A20(in hex)…
Q: b) The average memory access time for a microprocessor with 1 level of cache L1 is 2.6 clock cycles.…
A: Explanation: Consider the expressiono for miss rate of L1 cache. Given that: Hit time = 1…
Q: Let cache of 0.7 hit having average access time 9 times faster than that of memory. If average…
A: Here in this question a cache with 0.7 hit is given with access time 9 times faster than memory…
Q: Function NSU-1 For a system, RAM-64KB, Block size-4 bytes, Cache sine- 128 bytes, Direct mapped…
A: RAM -64 KB Block size -4 byte Cache size 128 byte Hit ratio while using direct mapped cache: To…
Q: Problem4: A microcomputer has the following memory map: 4100 to 410F I/O 2100 to 22FF RAM 0000 to…
A:
Q: 1. An intel high performance processor is executing multiple processes simultaneously. The processor…
A: The hit ratio is calculated by divideing the number of cache hits with the sum of the number of…
Q: C) If you want to Design 8K-byte memory starting from (B000)H by using a memory chip with size (4096…
A: As per the answering guidelines, solving the first 3 question. 1. Number of 4096x2 chips required =…
Q: On the Motorola 68020 microprocessor, a cache access takes two clock cycles. Data access from main…
A: step: 1 of 2 Preconditions: One clock cycle = 60 ns Given that, Cache access takes two clock cycles,…
Q: Answer the question below based on given portion of the memory unit with a word size of 8 bits, and…
A: Provided below is the detailed step by step explanation for finding the missing fields in the memory…
Q: For a system, RAM - 64KB, Block size - 4 bytes, Cache size - 128 bytes, Direct mapped cache.…
A: Given: RAM size = 64 KB Block size = 4 bytes Cache size = 128 bytes
Q: b) Machine cycle defines a loop process with four major components. Explain why machine cycle is…
A: Machine cycle has 4 phases: Fetch - Decode - Execute - Store
Q: 5. How many bits are required to address a 4M X 16 main memory if a) main memory is byte…
A: Dear student, As per guidelines. I can do only first question with both subparts. Please repost your…
Q: Suppose you are given with a ROM chip of size 1024*8 and 5 RAM chips of size 512*8. Show…
A: The formula for calculating RAM devices: This chip has eight bits. Because one byte requires eight…
Q: Can the virtual addresses 0x100000 and 0x100008 be mapped to 2 far apart locations in physical RAM?
A: To map virtual addresses to physical RAM, page tables are used. Virtual address space of a process…
Q: Problem Given the following memory values and a one-address machine with an accumulator, what…
A: a) Immediate addressing mode loads the constant value 20 as an operand to accumulate. AC=20
Q: Design the memory mapping between the Cache memory of 64MB to the main memory of 4 GB using 8 way…
A: For a 8-Way associative cache allows placement in any block of a set with 8 elements• 8 is the…
Q: Let (BX)=100H, DI=200H, DS=1200H, SI= FO02H, AX= 0105H, and the following memory content. what is…
A: Solution:
Q: Question 1: (a) Draw and Explain Memory Hierarchy. (b) Explain the three techniques of mapping…
A: Memory Hierarchy: The memory in a computer can be divided into five hierarchies based on the speed…
Q: Following is the memory map beginning from address 3C00H and increasing addresses to the right, all…
A: These instructions are used to transfer the data from the source operand to the destination operand.…
Q: Q1: Fill with the required information assuming that memory byte addressable using:
A: I have solved the problem & filled the table in the two ways mentioned in the question. If you…
Q: For a system, RAM - 64KB, Block size - 4 bytes, Cache size - 128 bytes, Direct mapped cache.…
A: Given:
Q: Compare between the following techniques that are used for computer memory cache: (A) Direct-mapped.…
A: In cache memory there are three types of mappings that are: Direct mapping Fully associative…
Q: A recent paper proposed eliminating paging and using segmentation instead. Their reasoning was that…
A: The design of RISC-V instruction sets is modular. Rather than take the approach of a large and…
Q: The following equation was suggested both for cache memory and disk cache memory Ts = Tc + M* T,…
A: The Answer is
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 1 images
- Design a Read Only Memory (ROM) to implement the following, A097803, polynomial A=3(2x2 +1), with input (x): 0≤(x)≤7 (a) What is the size of the initial (unsimplified) ROM ? (b) What is the size of the final (simplified) ROM ? (c) Show in detail the final ROM layout, using LogiSim.can you do letter C using Logisim APPthank you!Q1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000H to 3009H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending each of the required bytes, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes. The solution must be integrated and include the calculation of the baudrate delay time Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)The following equation was suggested both for cache memory and disk cache memory Ts = Tc + M * TD Generally this equation to a memory hierarch with N levels instead of just two levels. %3D
- c) To illustrate what difference a vector processor can make as compared to a traditional CPU, consider a hypothetical RISC machine with these lines of code ; Hypothetical RISC machine; add 10 numbers in a to 10 numbers in b, storing results in c; assume a, b, and c are memory locations in their respective registers move $10, count ; count := 10 loop: load r1, aload r2, badd r3,r1,r2 ;r3:=r1+r2store r3, cadd a,a,$4 ;moveonadd b,b,$4add c,c,$4dec count ; decrementjnez count, loop ; loop back if count is not yet 0 ret How would a Cray-style vector machine process this information? d.) State three advantages in the vector style approachQ1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending the required byte, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baud rate delay time Transmit Set up Character Bit Counter • Send Start Bit No Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes • Add Parity if Necessary Send Two Stop Bits Return (a)Design a Read Only Memory (ROM) to implement the following, A097803, polynomial A=3(2x2 +1), with input (x): 0≤(x)≤7 (a) What is the size of the initial (unsimplified) ROM ? (b) What is the size of the final (simplified) ROM ? (c) Show in detail the final ROM layout, using LogiSim.
- Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay timeMicroprocessor 8086 write An array called (A) has 300 unsigned byte numbers (chose your Owen data), write only one assemble to the following1-store the Maximum number of (A) in physical address AB200h. 2- store the Minimum number of (A) in the physical address CD100h. 3-rearrange the array given (A) ascending and save the new array in the memory starting at 3050e 4-save only the maximum odd number in the logical address 5200:0350The table below shows a segment of primary memory from a Von Neumann model computer Address Data 10101000 10001000 11001000 10011001 10100000 10101010 10110100 10111011 10001100 11001100 The program counter (PC) contains a value of 11001000. Find the value (in binary) that will be placed in MAR (memory address register)? MAR (in binray) %3D Find the value (in binary) that will be placed in MBR (memory buffer register)? MBR = (binray) %3D
- 6. Update memory values for the following code. Keep track of the loop counter (R16) and index register values as you go through the loop. LDI R16,3 R15, Y+ -Z, R15 LOOP: LD ST DEC R16 BRNE LOOP STS 0x0200, R28 CPU Register R28 (YLB) R29 (YB) R30 (ZUB) R31 (ZHB) Value OxFC 0x01 0x04 0x02 Data Memory Value 0x21 0x02 0x11 0x03 Address 0x01FC 0x01FD 0x01FE Ox01FF Ox0200 0x0201 Ox0202 Ox0203The use of transistors in the construction of RAM and ROM leads me to believe that there is no need for cache memory.The term "temporary storage" may also be thought of as "random access memory" (RAM) that is momentarily vacant. Imagine a machine that only had one kind of memory—is it even possible?Q5.Write a multiplication an Intel 8085 assembly program to multiply 2 numbers. The numbers are stored in memory locations 3000H & 3001H. Store the result in memory locations 3002H & 3003H. Show your flow chart and the assembly code. Q6. Answer True or False for the followings: a) Machine code is the assembly code b) Data field is 16 bit while address field is 8 bit c) Trainerkitcanbeused for implementing assembly code d) ADo bus can be used for addressing and datatransfer e) WR and RD pins are on the same pin