The five-bolt connection must support an applied load of P = 1600 lb. If the average shear stress in the bolts must be limited to 33 ksi, determine the minimum bolt diameter that may be used for this connection. 00000 VP

The five-bolt connection must support an applied load of P = 1600 lb. If the average shear stress in the bolts must be limited to 33 ksi, determine the minimum bolt diameter that may be used for this connection. 00000 VP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A line AB cannot be measured directly because of an obstruction on line. Accordingly, the two lines…

A: S1 = 2320.85m S2 = 1400.42m h = 155m Length of the line AD = d1 Length of the line DB = d2 To be…

Q: 2. Obtain the general solution. (Let 2C=C) (4x + xy²)dx + (y + x²y)dy = 0

A: From the given question it is required to determine the solution of differential Equation…

Q: particles, (ii) a biological process for removal of dissolved organic matter and fine suspended…

A: the waste-water treatment process consists of various processes such as screening grit removal…

Q: 2. Classify the following soil using AASHTO classification system. Description Percent finer than…

A: Solution: As per AASHTO classification system: Soil A: Sieve No. 200 = 38% passing Greater than 35 %…

Q: Explain the modes of failure in tension test.

A: A tension member of a structure is the component that may undergo tension force in the axial…

Q: Q1/ Classify the systems shown in Fig.(1) for stability and determinacy. M (b) Roller- (2) 2 Pa (c)

Q: 5.2 For the calculation of net area of flat with staggered bolts, the area to be deducted from gross…

Q: column spaced 9 m apart in two perpendicular directions. If the flat roof loading is estimated to be…

Q: Instructions Questions: 1. Recall concepts of statics and mechanics of rigid bodies. What are the…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: A solid cube of side 1 m is kept at a room temperature of 32°C. The coefficient of linear thermal…

A: Given- side=1 m,α=1×10-5 /oC,k=200 GPa, It is needed to find the volumetric stress.

Q: The beam below has a width of 400mm and a depth of 600mm. It has 2 hollow cores as shown below.…

A: Answer (A) Calculation of the distance of the neutral axis from top edge of the beam Let us…

Q: Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36…

A: Given : To Find : Pmax = ?

Q: Use the virtual work method to find: a. slope at A b. slope at B c. deflection at the midpoint of…

A: Using Virtual work method## calculation of slope at A and B and deflection at mid span of beam

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Q: new methods on analyzing structures under dead loads and moving loads in the recent time

A: Buildings in civil engineering are built to withstand a variety of loads and probable load…

Q: A shallow wide river 1500 m wide has a flow of 3000 m³/sec with a velocity of 1.5 m/sec. Manning's…

A: Given data nr =0.025 Lv=1:40 Lh= 1:800

Q: Explain Modern Drilled Shaft Construction

A: The term is related to geotechnical engineering.

Q: approach signal is divided into r = 74 seconds of effective red, followed by g = 16 seco ve green.…

A: given, cycle time, C = 90 sec effective red time, r = 74 sec effective green time = 16 sec rate of…

Q: A submarine is modeled as a cylinder with a length of 320 ft, a diameter of 50 ft, and a conning…

Q: The flow of glycerine (kinematic viscosity Vg = 5 x 104 m²/s) in an open channel is to be modeled in…

A: To determine the length scale (ratio of prototype to model dimension) for maintaining dynamic…

Q: The tractor shovel carries a 600kg load of soil, having a center of mass at G. Compute the member…

A: Given Required Force in member BC and IJ

Q: A cast iron pipe of diameter 600 m and length 400 m caries water from a tank and discharges freely…

Q: ACTIVITY 3 1. Classify the Soil 1 according to the USDA textural classification system. Soil 1…

A: To find out the soil according to USDA textural classification system.

Q: On a highway, if vehicle arrivals are "random," then headways follow a(n): Group of answer choices…

A: A crucial element in traffic flow planning is the simulation of a vehicle's entrance at a certain…

Q: Q3: for the wall shown: 3m 4m ↓ -2. 20kpa #G..T c'. 5okpa $=15₁ Y= 19.8 11eN/m³ c'= lookpa 410°, Y.…

Q: ention in details the classes of soil water.

A: The soil water is classified in following three types. Gravitational water Cappilary water…

Q: 1.3) The design strength based on fracture is A) 200.31 kips B) 240.38 kips C) 400.62 kips D) 412.00…

Q: AcL Cuzs Cam BD= 115 DF.75 FH= 25 left G12.75 HA IS right AB=0 CD=.5 Middle CF-S GH=0 (middle 27ราร…

Q: Problem#2: Determine the reactions of the beam. 300 lb io 100 lb/ft R1 R2 400 lb

Q: A stratified soil is to be analyzed for stresses. The stratified soil is composed of sand, silt,…

A: Given data in question Clay, Gravel, sand and silt Depths 3.6 ,2.8 , 4 and 3 m respectively. Water…

Q: Question 1 Table 1 shows the summary of a closed loop traverse carried out in campus by a group of…

Q: Problem 1.9 - Determine the magnitude and direction of the resultant force acting on the…

Q: A block of wood 0.20 m thick is floating in sea water. The SG of wood is 0.65 while that of seawater…

A: Given:Thickness of block=0.20 mspecific gravity of wood(swood)=0.65specific gravity of…

Q: E = 200GPa I= 7.5 x 10-6m* 300N/m 2m od, solve the 4m- and 600N/m 2m the 800N

Q: During a steady right turn, a person exerts the forces shown on the steering wheel. Note that each…

Q: Determine the reactions at the supports A and B of the compound beam. There is a pin at C.

A: Given : To Determine : Reaction at A and B ?

Q: 4. A 54 kg girl is walking up a 22kg uniform beam. The coefficient of friction is 0.2 at all…

Q: Each of the rods BD and CEIs made of brass (E=105 GPa) and has a cross-sectional area of 200 mm².…

A: Modulus of elasticity = E = 105GPa Area of the rod = 200mm2 Load P = 1KN To find - Deflection of…

Q: Determine the internal resultants FG, Vo G₁ G₁ C

Q: The maximum number of vehicles observed in any five minute period during the peak hour is 160. If…

Q: The frame carries a cylinder that weighs 80lb. Calculate the support reactions at C and D. Assume…

A: To Determine :- The support reactions at C and D.

Q: BkN C KN Y KN e the force in each member of the truss. Assume all

A: degree of static indeterminacy, Ds = m+ r -2j m = total number of members r = total number of…

Q: A man recorded 70, 71, 69, 73 paces in walking along a 50m course to determine his pace factor. He…

A: To Determine :- Distance AB Based on his pace factor.

Q: Coming home after the end of the winter semester, you find that your family’s swimming pool has not…

A: Given,Volume of pool =200 m31% Cl2 added into pool at the rate of =100 ml/hrinlfow of water=3.785…

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A 1:50 scale model of a spillway is to be tested in the laboratory. The discharge in the prototype…

Q: In the plot of cumulative vehicle arrivals and cumulative vehicle departure curves (y-axis) vs. time…

A: In the plot of cumulative vehicle arrivals and cumulative vehicle departure curves (y-axis) vs. time…

Q: Effluent from a wastewater treatment plant (flow 25°C) is rate = 8640 m³/d, temperature discharged…

A: Given data- Effluent Qw=8640 m3/d,Temperature Tw=25oC,andSurface stream Qs=1.2 m3/s,Temperature…

Q: Q1-A/ Determine the moment of the force system shown in Figure (1A) with respect to point A. 3 3 100…

Q: The precast floor beam is made from concrete having a specific weight of 23.6 kN/m3. If it is to be…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

100%

1) will upvote anyone who will answer

The five-bolt connection must support an
applied load of P = 1600 lb. If the average
shear stress in the bolts must be limited to
33 ksi, determine the minimum bolt
diameter that may be used for this
connection.
ooooo
VP

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 load on each bolt

VIEW

Step 2 minimum dia of bolt required

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 255 MPa, determine the minimum bolt diameter that may be used in the connection.
A flange bolt coupling consist of 8-12.7mm steel bolts on a circle diameter of 304.80mm & 6- 12.7mm steel bolts on a circle diameter of 228.60 mm. is subjected to a 950KN-mm torque.The shear stress developed in the outer circle of the flange bolt coupling is ____ MPa. A 4.30 B 8.10 (C) 1.50 6.80 3.20 E
The five-bolt connection must support an applied load of P = 2200 lb. If the average shear stress in the bolts must be limited to 44 ksi, determine the minimum bolt diameter that may be used for this connection. %3D coo00 Answer: dmin in.
For the clevis connection shown, the shear stress in the 0.287-in.-diameter bolt must be limited to 29 ksi. Determine the maximum load P (in kips rounded to the nearest hundredths) that may be applied to the connection.
The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear stress in the bolts must be limited to 174 MPa, determine the minimum bolt diameter that may be used in the connection. Answer: d = i mm.
A double angle ISA 75mm x 75mm x 8mm back- to-back welded to one side of a 12mm gussethave allowable stress 150MPa. Determine the allowable tensile load on the members and weldlength and overlap length of gusset plate.
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
What is the axial stress in the bronze rod (in MPa)? 2m 3m 6o kN mm 15mm banzerod
For the connection shown, determine the average shear stress produced in the 3/8- in. diameter bolts if the applied load is P = 2,500 lb. %3D O 5606 psi O 6559 psi O 2219 psi 6506 psi 5660 psi 1200 psi
For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress = 0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. 300 mm t/2 -P/2 P- -P/2
For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress=0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. P- O JAK O O 300 mm -P/2 -P/2