Thegear train shown transmits power from a motor to a machine at E. The motor turns at 808 rpm. The diameter of solid shaft (1) is1.50 in., the diameter of solid shaft (2) is 2.00 in., and the allowable shear stress for each shaft is 6 ksi. Determine the rotation speedof gear E.B72 teeth30 teethTE(2)24 teeth60 teeth

Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Answered: the diameter of solld snaft (2) IS E.…

Engineering

Mechanical Engineering

the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 1000 r.p.m. and the other at 2500 r.p.m., find the number of teeth on each wheel, if the module is 9 mm. Also determine the exact distance apart of the shafts.
Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A 40-mm diameter, 522-mm length shaft is drilled, for a part of its length L1, to a 20 mm diameter and for the remaining length L2 to a 30 mm diameter drill hole. If the allowable shear stress is 86 MPa, find the maximum power that the shaft can transmit at a speed of 226 rev/min. If the angle of twist in the length of 20 mm diameter drill hole is equal to that in the 30 mm diameter drill hole, find the length of the shaft that has been drilled to 20 mm and 30 mm diameter.
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. -20KW 7OKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O If segment Co is to be replaced ay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc = 392 lb-ft is removed from the shaft at gear C, and the remaining torque is removed at gear D. Assume that DA-4-in.-diameter, Dg=12-in.-diameter, L₁=56 in., and L₂-30 in. Segments (1) and (2) are solid 1.5-in.-diameter steel [G = 12200 ksi] shafts, and the bearings shown allow free rotation of the shaft. Determine: (a) the maximum shear stresses T₁, T₂ in segments (1) and (2) of the shaft. (b) the rotation angle D/B of gear D relative to gear B. Answers: (a) T₁ (b) D/B = = i ᎠᏴ ; A DA i B L₁ Tc amala ksi, T₂ = L2 i Tp D ksi.
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 86cm and 37cm respectively. If driven shaft runs with 10 r.p.s,determine the following; ( 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 8mm
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
Q.1) Two torques are applied to the solid bronze ( G= 6500 ksi) shafts of a gear system shown below. The diameters of shafts AB and CD are 1.25 inch and 1.0 inch, respectively. The shaft CD ix fixed at D and the bearings at A, B, and C are frictionless. Determine the maximum shear stress in each of the shaft and the rotation of end A. 10 in. 30 in. 80 lb·ft A 40 lb ft 8 in. 10 in. 6 in. B 4 in. 12 in.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The steel shaft DF consists of three concentric tubes and is supported by smooth bearings at D and E. It is coupled to a motor at F, which delivers 14 kW of power to the shaft while it is running at 52 rev/sec. The gears A, B, and C remove 3 kW, 5 kW, and 6 kW, respectively. The shaft is free to turn in its support bearings D and F. Determine the shearing stress developed in segments BC and CE.
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh. The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at each pair assuming equal direction of load between the pairs. Neglect friction.