The four gears shown are attached to a steelshaft that is rotating at 2 Hz. Gear B supplies70 kW of power to the shaft. Of that power, 20kWare used by gear A, 20 kW by gear C and 30kWby gear D.G=83 GPa for steel-20KWJOKN -20kw -30kW2m1.5m1.5mB(a) If a uniform shaft diameter of 125 mmB speci fied, detenmine the angle of rotationof A relative to D.O f segment Co is to be replaced lay a hollawShaft with an inside diameter of 80 mm,what is the outside diameter if the stressis not to excced 70 MPa.

Answered: Image /qna-images/answer/2fb4485b-fdf9-498e-a397-1c5de7e62f41.jpg

The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel

The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. -20KW 7OKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O If segment Co is to be replaced ay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7 kW, of which 30.4 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 57.3 mm, h = 68.9 mm, L = 4.2 m, M = 2.4 m, and G = 83.16 Gpa. Round off the final answer to two decimal places. A d Bh C | — L M →
The steel shaft with two different diameters rotates at 4.9 Hz. The power supplied to gear C is 54.1 kW, of which 26.9 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 55.5 mm, h = 68.9 mm, L = 4.2 m, M = 2.8 m, and G = 83.46 Gpa. Round off the final answer to two decimal places.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm2.
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
3. The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on their right ends engage a third gear that is attached to shaft 3. Determine the torques in shafts 1 and 2 when the 500N -m torque is applied to shaft 3. 40 500 Nm 80 Dimensions in mm 4. A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find the torque that will cause a maximum shear stress of 10 000 psi. Use G = 4 x 106 psi for aluminum. +4 in. → 0.04 in. 0.08 in.´ 5. Two steel springs are arranged in series as shown. The upper spring has 36 turns of 100-mm- diameter wire on a mean radius of 350 mm. The lower spring consists of 24 turns of 75-mm diameter wire on a mean radius of 245 mm. If the ultimate shearing stress in either spring must not exceed 692 MPa, (a) compute the maximum value of P and total elongation using factor of safety equal to 1.5. (b) What is the equivalent spring constant? Use G = 83 GPa. 2 of 2 4 in. wwwww.-
P-8. The steel shaft shown in the figure rotates at 6.40 Hz with 42 kW taken off at A, 27 kW removed at B, and 69 kW applied at C. Using G = 110 GPa. The angle of rotation of gear A relative to gear C is_ degrees. A B 55 mm ¢ 65 mm ¢ 4 m 2 m 2.289 4.573 6.057 9.552 O 11.374
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows: F,= 1590 N; F, = 580 N Pulley T1 Gear F, A D F, -100- 200- 100 All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa: Yield strength = 380 MPa; Factor of safety = 1.5.
The steel shaft with two different diameters rotates at 4.7 Hz. The power supplied to gear C is 74 kW, of which 43 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58 mm, h = 63.8 mm, L = 3.2 m, M = 2.3 m, and G = 83.34 Gpa. Round off the final answer to two decimal places. A d B h C ... –L - M→|
The steel shaft with two different diameters rotates at 4.4 Hz. The power supplied to gear C is 73 kW, of which 48 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 59 mm, h = 61.7 mm, L = 3.9 m, M = 2.5 m, and G = 83.34 Gpa. Round off the final answer to two decimal places.
A solid 1.5 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 lb-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 670 rpm? What is the maximum shear stress developed in the shaft? Convert the given shaft speed to units of rad/s. Answer: W = i rad/s