The concrete sections of a certain superhighway are designed to have a length of 24.0 m. The sections are poured and cured at 10.0°C. What minimum spacing should the engineer leave between the sections to eliminate buckling if the concrete is to reach a temperature of 44.0°C? (Note: If applicable, Table 1 is available for use in solving this problem.) cm

The concrete sections of a certain superhighway are designed to have a length of 24.0 m. The sections are poured and cured at 10.0°C. What minimum spacing should the engineer leave between the sections to eliminate buckling if the concrete is to reach a temperature of 44.0°C? (Note: If applicable, Table 1 is available for use in solving this problem.) cm

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter1: Temperature And Heat

Section: Chapter Questions

Problem 9CQ: Calculate the length of a 1-meter rod of a material with thermal expansion coefficient a when the...

See similar textbooks

Similar questions

One process for decaffeinating coffee uses carbon dioxide ( M=44.0 g/mol) at a molar density of about 14,0 mol/m3 and a temperature of about 60 . (a) Is CO2 a solid, liquid, gas, or supercritical fluid under those conditions? (b) The van der Waals constants for carbon dioxide are a=0.3658 Pa m6/mol2 and b=4.286105 m3/mol. Using the van der Waals equation, estimate pressure of CO2 at that temperature and density. `
Hi please help:A cylinder bore in an aluminum engine block has a diameter of 95.00 mm at 20.00 degrees Celsius A. What is the diameter of the bore when the engine operates at 120.0 degrees Celsius? Express answer using 4 significant digits and in mm. B. At what temperature is the diameter of the hole equal to 94.85mm? Express your answer using 2 significant figures.
A 214−g aluminum engine part at an initial temperature of 22.60°C absorbs 94.5 kJ of heat. What is the final temperature of the part (c of Al = 0.900 J/g·K)? Solve correctly please. Should correct
B- The gas in an internal combustion engine initially at temperature of 1250°C expands polytropically to five times its initial volume and( 1/6) its initial pressure. Calculate 1-The index of expansion n. C m onters a
Path: p Words QUESTION 4 At a constant temperature, a gas occupies 4.31 litres at a pressure of 0.755 atm. Determine the volume, if the pressure is inereased to 1.25 atm.? T T T Arial 3 (12pt) Path: p QUESTION 5 State the zeroth law of Thermodynamics? lịck Save and Submit to save and submit. Click Save All Answers to save all answers.
First Question: A. Using the definition of specific heat, the first law of thermodynamics and the ideal gas law, show that: (i) dQ = Cy dT +P dV, where Cy is the specific heat at constant volume, (ii) Cp = Cv + R, where Cp is the specific heat at constant pressure and R is the ideal gas constant. B. mol sample of hydrogen gas is heated at constant pressure from 300K to. 420K. Calculate (a) the energy transferred to the gas by heat, (b) the increase in its internal energy, and (c) the work done on the gas. %3D %3D
What would be the volume of 3.90 moles of an ideal gas, at STP? What is the pressure of this gas, if the temperature was increased from 0 degC to 56.9 degC as it stays in a constant volume container?
5 moles of an ideal gas are compressed to half the initial volume at a constant temperature of 27.0°C. Calculate the work done in the process. Given R 8.3 JK- mol-. Write your result up to appropriate significant figures.
ra solu QUE: A constant-volume gas thermometer (see the figures below) has a pressure of 5.28 x 103 Pa when the gas temperature is 0.00 °C. What is the temperature (in °C) when the pressure is 1.81 × 10³ Pa? Evacuated space Gas-filled bulb Reference lovel Substance whose temperature is being measured U-tube manometer Mercury Cin a constant volume as thermometer SUPPORT 121 ne gas ther... i a constant-... E Chegg SC C
A nozzle is a device for increasing the velocity of a steadily flowing fluid. At the inlet to a certain nozzle the specific enthalpy of the fluid is 3045 kJ/kg and the velocity is 70 m/s. At the exit from the nozzle specific enthalpy is 2850 kJ/kg. The nozzle is horizontal and there is a negligible heat loss from it. Determine; i. The velocity of the fluid at exitii. The rate of flow of fluid when the inlet area is 0.1 m2and the specific volume at inlet is 0.19 m3/kg.iii. The exit area of the nozzle when the specific volume at the nozzle exit is 0.5 m3/kg.
A large cylindrical tank contains 0.750 m3 of nitrogen gas at27C and 7.50 * 10^3 Pa (absolute pressure). The tank has a tight-fittingpiston that allows the volume to be changed. What will be the pressureif the volume is decreased to 0.410 m3 and the temperature is increasedto 157C?
ConstantS I PeriodiIc a If 11.00 mol of helium gas is at 17.0 °C and a Part A gauge pressure of 0.300 atm . Calculate the volume of the helium gas under these conditions. Express your answer using four significant figures. DA ΑΣφ V = 201.6 ? m3 Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Part B Calculate the temperature if the gas is compressed to precisely half the volume at a gauge pressure of 1.00 atm. Express your answer using two significant figures. ? T = °C Doorcon