The aluminum block has a rectangular cross sectionand is subjected to an axial compressive force of 8kip. If the 1.5-in. side changes its length to1.500132 in., determine Poisson's ratio and thenew length of the 2-in. side. Eal = 10,000 ksi.1.5 in.8 kip2 in.8 kip3 in.

Answered: The aluminum block has a rectangular…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 36 kN. If the 37 mm side changed its length to 37,5033 mm, determine Poisson's ratio and the new length of the 50 mm side. Ea-70 GPa. 36 kN- 37 mm 50 mm 36 kN 75 mm.
3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive force of 8 kips. The 1.5-in side changed its length to 1.50014 inches. Use E = 10 x 10³ ksi. Calculate the new length of the 2-inch side. Answer: Lnew = 2.00019 in 1.5 in 2 in. 8 kip- 8 kip 3 in. 4. A solid cylinder of diameter D is subjected to an axial load P. Show that its change in diameter is 8D = 4Pv/лDE.
Question 1: Given that Tuitow = 50 MPa for the rod AB and tattow = 25 MPa for the rod BC. If T=1250 N.m, find the required radius for both rods. Ahmtmum AB = BC =
Determine the compressive force (in Ib) in the bars shown after a temperature rise of 149°F if d = 0.012 in. Round off the final answer to five decimal places. d ... L M Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.73 sq. in E = 14930924 psi L = 13.4 in E = 10543748 psi L= 16 in a = 11.76 x 10-6/ °F a = 12.54 x 10-6/°F
= A cubic block with an edge of 0.2 m and a weight of 98 N lies on another cubic block of the same dimensions as the previous one whose module E 10x10⁹ Pa. If µ = 0.35, determine the deformed length.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 189.3 kN? Express your answer in four decimal places.
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
The timber member has a cross-sectional area of 1703 mm2 and its modulus of elasticity is 13.2 GPa. Compute the change in the total length (in mm) of the member after the loads shown are applied if x = 1.84, y = 3.63, and z = 4.11. Round off the final answer in two decimal places.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
Need asap A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN. If μ = 0.33 and E = 105 GPa. Determine the change in diameter. In mm. Thanks
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
What is the Share Force (in KN) at a point 0.6L (where L is the length of the plank) given that: F1 = 6.8' F2 = 14.6 F3 = 7.8 X = 4.3 y = 5.8 F1 kN F2 kN x m ym FakN B.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 8 kip. If the 1.5-in. side changes its length to 1.500132 in., determine Poisson's ratio and the new length of the 2-in. side. Eal = 10,000 ksi. 1.5 in. 8 kip 2 in. 8 kip 3 in.