The 100V source is absorbing 50w of power in the network shown in the Figurewhat is the value of R and what power delivered or absorbed by the currentsource of 5AR-..n, PSA=..wa- 27.71, 725, deliveringb- 17.27, 275absorbingc- 17.27, 275 deliveringd- 71.72, 572 absorbinge- 71.72, 572 deliveringf- 27.71, 725 absorbing102102R.200 V100 VAnswer:

Answered: Image /qna-images/answer/456f90ec-dccf-411c-8dd0-868f340d0512.jpg

The 100V source is absorbing 50w of power in the network shown in the Figure what is the value of R and what power delivered or absorbed by the current source of 5A R-.., PSA.w 102 100 a- 27.71, 725, delivering b- 17.27, 275absorbing c- 17.27, 275 delivering d- 71.72, 572 absorbing e- 71.72, 572 delivering f- 27.71, 725 absorbing R 200 v 100 V Answer:

The 100V source is absorbing 50w of power in the network shown in the Figure what is the value of R and what power delivered or absorbed by the current source of 5A R-.., PSA.w 102 100 a- 27.71, 725, delivering b- 17.27, 275absorbing c- 17.27, 275 delivering d- 71.72, 572 absorbing e- 71.72, 572 delivering f- 27.71, 725 absorbing R 200 v 100 V Answer:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Calculate the rms values of load voltage and current for the circuit shown below. Please show work
For maximum average power transfer in the circuit shown in the figure, set the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
When caluating the average power delivered to a bad by an AC sigre, it is not as straightforward as DC. It depere on the difference in phase between the sincecidal voltage across and current through the loadi, and it relates to the RMB values. The average power or enmetimas referred to as the active or real power, is related to the underpirning snusoidal voltage and current by P-Vene Cosy-00 W In this question there is only a resistive load, A-6.00 and the amplitude is 98V. Decame the amplitude of the curent through the load I- Workout the P 96V resistor, 6.80 50Hz V1 R1 6.80 Reset RUN/Stop Electric Potential Power Charge Simulation Speed Charge Flow Current Circuit:
Using PV Curve explain the effects of more real power, increasing excitation and how this helps maintain frequency. Describe the interlink between load angle and power.
You want to feed a load that works at 100Vrms and consumes 2KVA with a lagging power factor of 0.8. To supply the load, a transformer is required whose equivalent circuit is shown in figure b) and two sections of transmission lines shown in figure c). The general feeding scheme is shown in figure a). Without using the mesh or node methods, determine the power triangle of the power supply.
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Q5. Answer the following: Explain the power factor using a voltage and current waveform. How the power factor has the adverse effects on the power system quality. What are triplen harmonics? Why these are significant or what are there consequences on transformer and the machines? Explain the five types of voltage disturbances using waveforms, which affect the power quality in distribution system.
A 2000 KVA, 6600/400V , STAR/Delta was performed with short circuit and Open circuit test with the following results: O.C. Test : 400V, 150A and 15kw S.C. Test: 400V, 175A and 17kw Determine the percent impedance drop for resistance, reactance and impedance. Also calculate for the efficiency at half load, 0.80pf lagging and full load, 0.85pf leading.
OR e) What is BILS? Explain their significance in power system studies.
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)