Q5. Answer the following: (i) (iii) Explain the power factor using a voltage and current waveform. How the power factor has the adverse effects on the power system quality. What are triplen harmonics? Why these are significant or what are there consequences on transformer and the machines? Explain the five types of voltage disturbances using waveforms, which affect the power quality in distribution system.

Q5. Answer the following: (i) (iii) Explain the power factor using a voltage and current waveform. How the power factor has the adverse effects on the power system quality. What are triplen harmonics? Why these are significant or what are there consequences on transformer and the machines? Explain the five types of voltage disturbances using waveforms, which affect the power quality in distribution system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Make a conclusion regarding about the topic effect of frequency on transformer rating .
7. The primary of a single-phase transformer takes 1 A at power factor of 0.4 when connected to a 240-V, 50-Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. What is now the value of the primary current ? transformer.) (Neglect the voltage drops in the
Describe the effects of harmonics on power distribution system.
How to generate 480V three phase 400Hz ac from 230V three phase 60Hz ac source? (Please specify the power components you pick, such as transformers, dc-dc converter, dc-ac converter and/or ac-dc converter, how these components are connected and the key parameters of these components, such as the turns ratio of transformer and the duty cycle functions for the converters.)
The statement given in which option related to transformers is wrong.A) Power transformers are used as step-down transformers in step-up consumption centers in production centers. B) Current transformers for measuring current at high voltageVoltage transformers are used to measure voltage. C) Voltage adjustment can be made with the on-load tap changing feature of power transformers. D) Transformers are of great importance in reducing power losses by increasing the power value in energy transmission. E) If there is no reactive power in energy transmission with direct current, the transformer cannot be used.
5. Write down the equations of a single phase transformer at no-load mode. Give the names of the resistances, reactance, e.m.f.'s, currents and voltages.
A power transformer with standard insulation class of 69 kv will withstand an rms test voltage of A. 140 kv. B. 350 kv. C. 69kv. D. 440 kv.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
Q5. A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage reactance of 0.240. The low voltage winding resistance is 0.05 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent circuits)