Please answer with complete solution and brief explanation. Thank you. 12. A rope and pulley system is used to support a body W as shown. Eachpulley is free to rotate. One rope is continuous over pulleys A and B;the other is continuous over pulley C. Determine the tension T in therope over pulleys A and B required to hold body W in equilibrium ifthe mass of body W is 175 kg. Ans. T = 429NBAW

Given W=175kg Convert into Force W=175*9.81 N

Answered: solution

Engineering

Civil Engineering

solution

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Strength of Materials. 5.4 Assuming a density of 120 #/ft.3 for masonry brick- work, determine the…

Q: In the reinforced beam section shown in the figure (not drawn to scale), the nominal cover provided…

A: Given- cover=50 mm,diameter of the main reinforcement bar=16 mm,diameter of the strirrups=12 mm, It…

Q: 3. Draw the free-body diagram 4. Write the equilibrium equations 5. Apply the method of sections at…

Q: A uniformly distributed line load of 500 KM acting on the ground surface based on Boussinesq's…

A: Boussinesq's theory Assumptions soil mass is semi-infinite homogeneous and isotropic linear…

Q: 13. The roof truss shown is supported by a roller at A and a hinge at B. Find the values of the…

A: This question is related to the Structure Analysis from Civil Engineering. "Since you have asked…

Q: Lesson 1 1. A rigid frame is fabricated by joining the three bars with pins at B, C, and D, as…

A: The hinged support will have horizontal and vertical reaction. The roller support will have vertical…

Q: Is Graphene Coating In Construction a specific Product , Process or System? Also tell the objectives…

A: Concept- Carbon is the main component of graphene. With the use of graphene, a composite material…

Q: At the position shown, the end A of the od has a rightward component of velocity of 0.6 m/s and a…

Q: A rectangular concrete beam has a width of 300mm and an effective depth of 450 mm to centroid of the…

A: Given: b = 300 mm d = 450 mm Ast=6×π4×322=4825.5 mm2Asc=2×π4×282=1231.5 mm2 fc = 34.5 MPa fy =345…

Q: Three forces acting on the table as shown in the figure below. What is the magnitude and direction…

Q: A noise meter located at a distance of 30 m from a point source recorded 74 dB. The reading at a…

A: Given data: Distance of 1st noise meter, R1=30 m Distance of 2nd noise meter, R2=60 m Sound recorded…

Q: 1. Resolve the couple-force system into a single resultant force and a single resultant moment at A.…

Q: A solid circular torsional member OPQ is subjected to torsional moments as shown in the figure (not…

Q: A freshly cut log floats with 2/3 of its volume protruding above the water surface. a) Determine the…

Q: 300 mm 30° 300 mm 300 mm Can some one please label the projection of F and the rest of the…

A: Solution: The force vector F and uOA:

Q: Don't waste my question. Only correct answer please. Otherwise downvoted. A sewage pipe discharges…

A: Given data in question Velocity = 0.2 m/s Elevation = 2 m Sewage pipe To find out Total energy…

Q: Find the maximum end moment capacity of a simply supported beam with W24 x 55 section, where Lb= 150…

A: Answer Let us first calculate Lp and Lr Lp = 1.76ryEFy Lp = 1.76*1.34*2900036 Lp = 66.94 in Lr =…

Q: Chlorine is used as the disinfectant in a municipal water treatment plant. It achieves 50 percent of…

A: Given:t1=3 minutesη1=50 %t2=?η2=99%

Q: Constant

Q: Compute the elevation (orthometric height) for a station whose geodetic height is 113.991 m, if the…

A: N=-79m h=113.991m To find orthometric height

Q: Example The compressive gravity axial load for a building column are: L = 300 k, D = 150 k and L₁ =…

A: Given: DL= 150 k LL = 300 k Lr = 60 k Wc = 70 k Ec = 50 k Wt = -60 k Et = -40 k

Q: Using Terzaghi theory find the ultimate bearing capacity for a square footing of 2.0 m x 2.0 m…

A: Given- Square footing, Dimensions 2 m×2 m,depth of footing Df=1.2 m,pure cohesive soil,density γ=18…

Q: Problem 2. Determine the required magnitude of F1, F2, and F3 so that the resultant couple moment is…

A: Given: F4 = 150 kN -F4 = -150kN The Position of vectors r1, r2, r3 and r4.

Q: Problem 4. Replace the three forces acting on the plate by a wrench. Specify the magnitude of the…

A: Given :

Q: Investigate the flexural adequacy of the beam sections of figures 1 and 2 to carry the given loads…

A: Solution:-The given diagram is shown below, To Determine ,To investigate the flexural adequacy of…

Q: 1.13 List the legal requirements for registration as a land surveyor in your state. 1.14 Briefly…

A: There are different eligibility criteria to become a land surveyor. One should need to fulfill all…

Q: A track has a sleeper density of N+8. If tack is laid with welded rails of 44 m length, then the…

A: given- sleeper density=N+8,length of each rail=44 m/2 =22 m,length of railway track=1400 m.

Q: The long chord from the P.C to the P.T of a compound curve is 270.94 meters long and the angles its…

Q: Design an acrated grit chamber with 2 channel (Volume Dimensions, Total air Supply required and…

Q: The maximum and minimum shear stresses in a hollow circular shaft of outer diameter 20mm and…

A: Given data- Outer diameter D=20 mm. thickness t=2 mm. torque T=92.7 N-m. To Find- Maximum &…

Q: 4- A water tank has a right angle triangular cross section as shown in the figure. Its height is…

Q: A grit chamber of rectangular cross-section is to be designed to remove particles with diameter of…

Q: What is a geodetic coordinate system?

A: There are two coordinate systems for geographic data:- a) Geodetic coordinate system:- They are…

Q: A A 000 -4 ft B D - 4 ft 450 lb 4 ft

Q: A horizontal water jet with a velocity of 10 m/s and cross-sectional area of 10mm² strikes a flat…

A: given- density ρ=1000 kg/m3velocity of water u=10 m/sarea A=10 mm2

Q: P11.30b For the beams and loadings shown below, assume that EI= 5.0 x 104 kN-m² is constant for each…

A: 1. Concentrated moment M 2. Reactions at support B 3. Deflection at point A

Q: Problem 2 The body on the 30° incline is acted upon by a force P inclined at 20° with the…

A: First we will calculate the y component of the force. This will be done by using trigonometry…

Q: Prob.5. Samples of a dry sand are to be tested in triaxial and direct shear test. In the triaxial…

A: Given, Major principle stress, σ1 = 960kN/m2 Minor principle stress,σ3 = 260kN/m² Normal stress=…

Q: lem 2. A steel tape weighing 0.85 kg has a cross-sectional a res exactly 30.00 m when supported…

A: Given data, Total weight of tape = 0.85 Kg area of cross-section = 0.05 cm2 Nominal length = 30m…

Q: An airport has 4 gates which are available for all the aircraft it serves, an aircraft having…

A: Given- Number of gates G = 4, Average gate occupancy time T = 42 minutes. Utilization factor V =…

Q: Assuming that the beam section has cracked, determine the moment capacity of the beam section below…

Q: Back at Tinker Air Force Base, an aircraft seam requires 25 rivets during an MRO operation. The seam…

A: Solution:-To calculate the requisite probabilityTo Determine ,(a) The probability that a rivet is…

Q: Problem 2. Calculate the area of the closed traverse or field in square meters (using coordinate…

A: Given data: Chainage (m) 0 25 50 75 100 125 150 Offset (m) 0 5.49 9.14 8.53 10.67 12.5 9.75…

Q: Two steel spheres of diameters d, and d, where d₂= 2d,, are dropped from rest at the free surface of…

Q: A 5% of Rediset is used by the weight of asphalt binder to produce a WAM specimen has 1080 gm…

Q: 9. A surveyor sets up a transit at a point Q which is at the middle portion of a four-sided tract of…

Q: ord, find the radius of the second curve in meters.

Q: Give an insight and reflection about this "Health and Safety in the Construction Industry in…

A: Health and safety is usually concerned in areas or countries where there is development promotion…

Q: B9

A: Draw FBD at joint D: where, Sinθ1=0.49Sinθ2=0.18Cosθ1=0.87Cosθ2=0.98

Q: Problem 5 Specific Gravity (Gs) Saturation Water content 2.66 100% 49% e = n = Y = % lb/ft³

A: Reference : Soil Mechanics. Void ratio is given by ; S × e = w × G e = wGS Where ; S = Saturation =…

Question

Please answer with complete solution and brief explanation. Thank you.

12. A rope and pulley system is used to support a body W as shown. Each
pulley is free to rotate. One rope is continuous over pulleys A and B;
the other is continuous over pulley C. Determine the tension T in the
rope over pulleys A and B required to hold body W in equilibrium if
the mass of body W is 175 kg. Ans. T = 429N
B
A
W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

с d = 20 mm Al 20 kN 30 kN 15 kN D d = 15 mm B k 6 m 2 m 2 m 4 m 2 m A beam is suspended by a rod (6 m in length) at each end and is subject to three concentrated loads as shown. You may assume that the support conditions at A and B can be approximated as a roller. Rod AC has a diameter of 20 mm and rod BD has a diameter of 15 mm. Both rods are steel with Young's modulus E = 200 GPa and failure stress ofail = 350 MPa. a) Draw the free body diagram (FBD) for the beam and each rod. b) Determine the tensile force in each rod. c) Determine the tensile stress in each rod. d) What is the maximum factor if safety (FS) on fail that can be adopted if the design shown were to be viable? e) Determine the normal strain and elongation for both rods.
250 N 22. HAPPY 40 -KON 160 100 cam 120N JOON 250 Four forces are applied to the machine component ABDE as shown. Replace these forces with an equivalent force-couple system at A. After part a above, what would the support reactions be for equilibrium?
3. The roof truss is subjected to the loadings shown. Determine the force in each member and indicate if the members are in tension or compression. Approximate each joint as a pin. 200 N 300 N 300 N 1.5 m D. B. 4 m 3 т G 3 m 3 m E 3 т Paist X Ute 150 N
Q2/ Determine the resultant moment of the force about point D F=400N 100 N D 30 A B 45 0.3 m 100 N 0.4 m tazm t
2. The structure, the plan of which is shown below, supports a udl of 1kN/m over lengths AB, BC, DE, and EF, and a udl of 2kN/m over the length CD. Determine the moment, torque and shear at each of the fixed ends. Given: EI = 3GJ. A B 2m D C E F 4m 4m + 4m [Solution: S-10kN; T-3.53kNm; MA-27.5kNm] 2m
Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support tension only. Forces are positive if in tension, negative if in compression. 4 KN 7 KN at ling 2 m B 2 m Vc 2 m 67 67/ 67 67% Answers: AB= i BH = i H BG= i G F E kN kN kN
The frame shown supports a mass of m=250kg mass suspended from point F. The frame is supported by a pin connection at Point A and a roller at Point D. Internal pin connections are located at Points B, C, and E. The dimensions of the frame are h1=0.7m, h2=1.6m, h3=0.5m, L1=1.2m, L2=0.4m. Determine: The vertical and horizontal components of the reaction force at Point A. The vertical and horizontal components of the force at Pin C. The reaction force at Point D.
Determine the vertical and horizontal reactions of the hinge support if the weight of M object is FN Kilonewton, value of a = SN and b = MN meters. The equivalent of 0 is 30 degrees Note: MN = 88 FN = 88 SN = 47 a Hinge b Cable m Beam com M Rope
B. Beams Design WD = 26 kN/m WL = 20 kN/m 5 m- a. What is the ultimate uniform load? b. What is the ultimate Moment based on the beam's Moment diagram?
Problem 4: The bar ABC of negligible weight is supported by a pin at A and a rope that runs around the small pulley at D and the 10-kg homogeneous disk. a. Determine the tension in the rope. b. Determine Ax and Ay. D 450 mm 240 mm B 10 kg -450 mm 1350 mm
3. The assembly shown in Figure 1.3a, which carries a load of 30 kN, consists of two beams ABCD and CEF, and one bar BE, connected by pins; it is supported by a pin at A and a cable DG. The dimensions are in meters. Find (a) The components of the forces acting on each member and (b) The axial force, shear force, and moment acting on the cross section at point G. Assumptions: Friction forces in the pin joints will be omitted. All forces are coplanar and 30 kN IF Cable B 2D. YA K60° ↑ RAy
The bar ABC of negligible weight is supported by a pin at A and a rope that runs around the small pulley at D and the 10-kg homogeneous disk. a. Determine the tension in the rope. b. Determine Ax and Ay.