Question 3) The rigid beam CD in the figure is attached to the ceiling with AC and BD rods. The length of the AC rod is L AC =2 m, its diameter is d AC =11 mm, and its modulus of elasticity is E AC = 70 GPa . The bar BD has a length L BD =0.7 m, a diameter d Bp =25 mm and a modulus of elasticity E BD = 94 GPa . The length of the rigid beam CD is L CD = 1.5 m and the point E is in the middle of the rigid beam CD. According to this; CD rigid beam w=53 kN/m when a distributed load of the same size acts; A LẠC LcD LBD •E w kN/m Question 3-A ) Find the vertical displacement of point C(8c). (Write your result in mm .) Response: Question 3-B) Find the vertical displacement of point D(8p). (Your result mm in size of your text.) Response: Question 3-C) Find the vertical displacement of point E ( SE ) .( Write your result in mm .)

Question 3) The rigid beam CD in the figure is attached to the ceiling with AC and BD rods. The length of the AC rod is L AC =2 m, its diameter is d AC =11 mm, and its modulus of elasticity is E AC = 70 GPa . The bar BD has a length L BD =0.7 m, a diameter d Bp =25 mm and a modulus of elasticity E BD = 94 GPa . The length of the rigid beam CD is L CD = 1.5 m and the point E is in the middle of the rigid beam CD. According to this; CD rigid beam w=53 kN/m when a distributed load of the same size acts; A LẠC LcD LBD •E w kN/m Question 3-A ) Find the vertical displacement of point C(8c). (Write your result in mm .) Response: Question 3-B) Find the vertical displacement of point D(8p). (Your result mm in size of your text.) Response: Question 3-C) Find the vertical displacement of point E ( SE ) .( Write your result in mm .)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
A rigid bar of negligible weight is supported as shown below. Compute the value of the load W that will cause the stress in the steel rod to be 55 MPa. Bronze L = 3 m A = 1300 mm? E = 83 GPa Steel L = 1.5 m A = 320 mm? E = 200 GPa - 1 m %3D 2.5 m 1.5 m w/
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in^2, determine the stress in each section. Steel Bronze 4P | Aluminum | P 2 ft 3 ft 2.5 ft а. Stress (st) = 19 ksi, Stress (al) = 25 ksi O b. Stress (st) = 16.5 ksi, Stress (al) = 24.2 ksi O c. Stress (st) = 24 ksi, Stress (al) = 18 ksi O d. Stress (st) = 26 ksi, Stress (al) =17 ksi
2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (sce figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile load P = 22 kN? (b) If the same volume of material is made into a bar of constant diameter d and length 2.4 m, what will be the clongation under the same load P? (c) If the uniform axial centroidal load q = 18.33 kN/m is applied to the left over segment 1 (sce figure part b), find the ratio of the total elongation of the bar to that in parts (a) and (b). Įd1 = 20 mm Įd2 = 12 mm %3D P= 22 kN 1.2 m- -1.2 m (a) q = 18.33 kN/m [d1 = 20 mm |d2 = 12 mm P = 22 kN 1.2 m (b)
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B; = 0.8 m; B; = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 B3 10KN 15KN 30KN
Problem 1: The steel rod is placed inside the copper tube, the length of each being ex-, actly 15 in. If the assembly is compressed by 0.0075 in., determine the stress in each component and the applied force P. The moduli of elasticity are 29 × 106 psi for steel and 17 x 10° psi for copper. 0.6 in. 0,75 in. Problem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, 15 in. is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooleď? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. 0.125 in. Problem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D +1.5 m -3 m 3 m
2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (see figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile %3D %3D load P = 22 kN?
The beam shown in the figure below is subject to a moment of M = 17 kN.m as illustrated. Calculate the maximum tensile and compressive bending stresses. |-75 mm - - 12 mm B 12 mm 12 mm 75 mm 250 mm D 12 mm
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar Bị in kN. 35KN B1 B2 B3 ... 10KN 15KN 30KN Determine the axial load acting on bar B2 in kN. Determine the axial load acting on bar B3 in kN. Determine the axial stress of bar B1 in MPa. Determine the axial stress of bar B, in MPa. Determine the axial stress of bar B; in MPa. Determine the total deformation of the bars B1, B2 and B3 in mm. Determine the deformation of the bar B1 in mm. Determine the deformation of the bar B, in mm. Determine the deformation of the bar B3 in mm. 35 (A) 35 в) 20 10 (D 5
200KN A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of each material are shown in the figure. A fixed support is rigidly attached to the right end of the bronze rod. Determine the stress each section in kPa. Aluminum Steel D=28mm D=20mm 20KN Bronze D=25mm 150KN
A rigid plate ABCD is subjected to forces as shown in Figure below. Compute the magnitude of the resultant (in KN) of the system with reference to the point A.
The composite beam shown in the figure is simply supported and carries a total uniform load of 90 kN/m on a span length of 4 m. The beam is built of a wood member having cross-sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 50 mm × 150 mm. The moduli of elasticity are Es = 214 GPa and Ew = 11 GPa. (a) Determine the maximum stress in the steel. (Disregard the weight of the beam. Round to one decimal place.) (b) Determine the maximum stress in the wood. (Disregard the weight of the beam. Round to one decimal place.)