Refer to the given figure as shown. P= 40 kN Cross section Area: 50mm x 50mm Modulus of Elasticity: 70 GPa P D 4 m B 3 m EA = constant Determine the force in member BC in kN. Express your answer in nearest whole number. Indicate (-) if compression. Determine the unit stress in member AC. Express your answer in 2 decimal places. Neglect sign. Determine the horizontal displacement at joint C in mm. Express your answer in 1 decimal place. Neglect sign. Determine the vertical displacement at joint D in mm. Express your answer in 1 decimal place. Neglect sign.

Refer to the given figure as shown. P= 40 kN Cross section Area: 50mm x 50mm Modulus of Elasticity: 70 GPa P D 4 m B 3 m EA = constant Determine the force in member BC in kN. Express your answer in nearest whole number. Indicate (-) if compression. Determine the unit stress in member AC. Express your answer in 2 decimal places. Neglect sign. Determine the horizontal displacement at joint C in mm. Express your answer in 1 decimal place. Neglect sign. Determine the vertical displacement at joint D in mm. Express your answer in 1 decimal place. Neglect sign.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
3. The bar shown has a diameter of 2 in. and is made of an elastic-perfectly material with the stress-strain behavior as shown. If a force of P= 110 kip is applied to the bar, determine the stress in the segments AC and AB. o (ksi) P 20 |C B -2 ft - 3 ft e (in./in.) 0,001
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E, = 200 GPa , and E, 150 GPa E, = = 200 GPa 4 kN/m 20 mm 60 mm BA E E2 = 150 GPa 20 mm 50 mm 5 m 3 m |-1.5 m--1.5 m-- 3 m
tate of Stress Caused by Combined Loadings Learning Goal: To use the superposition principle to find the state of stress on a beam under multiple loadings. The beam shown below is subjected to a horizontal force P via the rope wound around the pulley. The state of stress at point A is to be determined. 100 mm 15 mm 20 mm 200 mm 150 mm f 20 mm The dimensions are di - 2.15 m. d₂ = 0.5 m. -0.85 m d-285 mm and r= 150 mm The applied force has magnitude P=4.5 kN Part A-Support Reactions and Internal Loading C₁, C₂=₁ N=, V = ₁ M = Determine the support reactions C, and C, and the internal normal force, shear force, and moment on the cross-section containing point A. Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) Submit Part B- Properties of the Cross-Section A= I= Q = Submit VAX IT VOC JA=.TA= What are the cross-sectional area, moment of inertia with respect to the neutral axis, and first moment of the area with respect to point A for the…
The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A = 4 mm between the lower end of the left rod and its pin support at C. %3D Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm? for rod BD. Use E = 200 GPa for steel. A В 0.75 m 1.5 m > 2 m D
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m
Question 1 Refer to the given figure as shown. P= 70 kN Cross section Area: 50mm x 50mm Modulus of Elasticity: 70 GPa 2P S! 4 m 3 m EA = constant Determine the force in member BC in kN. Express your answer in nearest whole number. Indicate (-) if compression. Determine the unit stress in member AC. Express your answer in 2 decimal places. Neglect sign. Determine the horizontal displacement at joint C in mm. Express your answer in 1 decimal place. Neglect sign. Determine the vertical displacement at joint D in mm. Express your answer in 1 decimal place. Neglect sign.
Situation 4: The bar ABC consists of 2 cylindrical segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress (ksi) in segment AB if the cross-sectional area of segment AB is 4.7 in². Use P₁ = 11 kips P₂ = 6 kips P₁ B C P₂ Consider the sign in your final answer. Use the sign convention (+) for tension and (-) for compression.
3: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that P= 10 kips, find the average normal stress at the midsection of (a) rod AB, (b) rod BC. 3:23M 1.25in 12 kips 0.75 in 12 Ap 678
2) The rigid bar ABC is horizontal before the load Pis applied as shown in the figure. Determine the maximum safe value of P if the stress in the steel bar is limited to 300 MPa and the stress in copper bar is limited to 140 MPa. Use E = 200 GPa for steel and E = 120 GPa for copper. Neglect the weight of the bar ABC. E suges. steel bar: copper bar: A=520mm? A=320mm? A 2.00m 1.00m 1.00m 1.00m 1.50m
Q.3) The Figure shown a beam with all dimensions. (a) Determine the bending stress at point H. 180 mm State whether the normal stress at H is tension or 12 mm compression. If the bending stress at point K is 9.0 MPa (Т). (b) Determine the magnitude of the maximum bending moment M: that can be supported by the beam. If the allowable bend 20 mm| 30 mm 260 mm stress is 165 MPa.
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.