Pls help with questions no.24 Question 24In the same setup as in question 23, if the mass of the crane arm (including winch) is 100 kg, find thedistance between the pivot and the center of mass for the crane arm (including winch).T2 = 4500 NLocation of center of massfor am of crane53PivotT1 = 650 N2 m6 m A winch mounted at the end of a crane arm is lowering a block of concrete on a cable. The tension in thecable is T1 = 650 N. The crane arm is supported by a second cable that pulls up on the arm at an angle of53° with respect to horizontal. The center of mass for the crane arm (including the winch) is marked with anx on the diagram.T2 = 4500 NLocation of center of massfor arm of crane53PivotT1 = 650 N2 m6 mFind the torque (magnitude and direction) exerted on the arm by the support cable (about the pivot point).

Given data mass of crane arm (m) = 100 kg Tension (T1) = 650 N Tension (T2) = 4500 N To…

Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is 100 kg, find the distance between the pivot and the center of mass for the crane arm (including winch). T2 = 4500 N Location of center of mass for am of crane 530 Pivot T1 = 650 N 2 m 6 m

Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is 100 kg, find the distance between the pivot and the center of mass for the crane arm (including winch). T2 = 4500 N Location of center of mass for am of crane 530 Pivot T1 = 650 N 2 m 6 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
The system in the Figure is in equilibrium. A mass M1 = 246.0 kg hangs from the end of a uniform strut which is held at an angle theta = 40.0o with respect to the horizontal. The cable supporting the strut is at angle alpha = 24.4o with respect to the horizontal. The strut has a mass of 58.2 kg. Find the magnitude of the tension T in the cable. Find the magnitude of the horizontal component of the force exerted on the strut by the hinge? Find the magnitude of the vertical component of the force exerted on the strut by the hinge?
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
At the top of a steel pole, there are two cables as shown in the figure. It is known that the weight of the pole is vertical and that the force applied horizontally at the top of the pole is 2500 N. If the 2500 N force is parallel to the z-axis (alpha=90), calculate the Tension in each cable (T1-3 and T1-4).
A) A mass of 15.0 kg 10 points suspended by wires in two sides as shown in the figure. Find the tension in each side T1 and T2, neglecting the mass of the wires. T1 T, T т, 30°- 1450
The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents weigh WL = 623 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.
4. The access door in Fig. P6-13 is held in the position by cable AB. If the magnitude of tension T in the cable is 50 pound force, find the rectangular components of T acting at A. 10 in. B 10 in. 12 in. 6 in. 20° FIGURE P6-13
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=250 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is γ=6°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=40°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
2. Auniform bar 3.00 m long is held by ropes at the ends making angle 60.0° and 30.0°, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0° rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.) 3.00m T2 7 0.500m 60.0 B 200 N
The following figure shows a hollow piston of weight W=50 N and diameter D=3d occupies the position initial displayed. The lateral tube has a diameter d₁=d/2. Find the descent of the piston for the equilibrium position. (b=12 cm, d=8 cm, y=104 N/m³). TBL Agua D d₁