The following forces are acting on the bracket below (a free-body diagram of the bracket is shown), that is hinged at point 1 (bottom left point). The bracket is in equilibrium (not accelerating). In this case we are pushing up on the far right hole with a force F3=62 lbf. What must the force at point 2 (F2 and give you answer as Ibf) be knowing it must act horizontally? F2 3 inches F1x 12 inches F3

The following forces are acting on the bracket below (a free-body diagram of the bracket is shown), that is hinged at point 1 (bottom left point). The bracket is in equilibrium (not accelerating). In this case we are pushing up on the far right hole with a force F3=62 lbf. What must the force at point 2 (F2 and give you answer as Ibf) be knowing it must act horizontally? F2 3 inches F1x 12 inches F3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following forces are acting on the bracket below (a free-body diagram of the bracket is shown), that is hinged at point 1 (bottom left point). The bracket is in equilibrium (not accelerating). The force at point 2 must act horizontally, but can act to the right or left. I drew the force acting at point 2 (the middle point) pushing the bracket to the right. For the given forces, did I draw the force acting on the bracket in the correct direction? F2 F1x 10 Ibf Yes No Can't be determined based on the given information
A truss is facing a two-force member and both of them are in the opposite directions, and the truss is in equilibrium. And both of them are coming to each other. The forces are called Select one: O a. Tensile Forces O b. Compressive forces O c Parallel and collinear forces with same direction of heading O d. The rotational forces Next page est-3 Jump to...
PS2-5 Three forces are acting on the problem. List all of the simplifications that can be used in the problem. What is the simplest problem? F₂ 45° R
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
The jaws and bolts of the wood clamp in Fig- are parallel. The bolts pass through swivel mounts so that no moments act on them. The clamp exerts forces of 300 N on each side of the board. Treat the forces on the boards as uniformly distributed over the contact areas and determine the forces in each of the bolts. Show on a sketch all forces acting on the upper jaw of the clamp. D 100 mm 150 mm B H00 mm75 mm-100 mm-
4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.
A sukelco post is subjected to forces acting upon it due to electrical cables attached to it. F1=60N north, F2=80N west and F3=120N, 45° south west. at what direction and force shall a buy wire be located to prevent the toppling?
Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
tv wil The following forces are acting on the bracket below. The bracket has a width w of 2 inches and a height h of 3 inches. The bracket is in equilibrium (not accelerating). Determine F3y knowing F1x-98 lbf and F1y-166 lbf. For this question, what is F3y in Ibf? Note that the y-direction is pointing up, so if the force is pushing down on the bracket, it has a negative magnitude. h 3,
Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response