Answered: If BX=1000, DS=0200, SS=0100, CS=0300…

Name: QI) If BX=1000, DS=0200, SS=0100, CS=0300 and AL-EDH, for the followi
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: QI) If BX=1000, DS=0200, SS=0100, CS=0300 and AL-EDH, for the followinginstruction:MOV [BX] + 1234H, AL.Find the physical address in the memory.

Engineering

Computer Science

If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] + 1234H, AI. Find the physical address in the memory.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter11: Operating Systems

Section: Chapter Questions

Problem 30VE

See similar textbooks

Similar questions

Memory address Data According to the memory view given below, if RO = Ox20008002 then LDRSB r1, [r0, #-4] is executed as a result of r1 = ?(data overlay big endian)? Øx20008002 ØXA1 Øx20008001 ØXB2 Øx20008000 Øx73 ØX20007FFE ØXD4 ØX20007FFE Lütfen birini seçin: O A. R1 = 0X7F O B. R1 = Oxffffffd4 O C. R1 = Oxffffff7F O D. R1=0XD4000000 O E. R1 = 0XD4
3. Calculate the physical memory location for each of the following cases? a- The logical address D470H in the extra segment. b- The logical address 2D90H in the stack segment. C- MOV [BP],AL if BP=2C30H. Assume ES=52B9, SS=5D27, DS=E000, and CS=B3FF.
Q) MOV CX, [481d] ; assuming DS= 2162H, logical address will be?
Assume that CS=3500, DS=4500, SS=5500, SI=2200, DI=4200, BX=7300, BP=8000, AX=3420 (all values are in hex). Calculate the physical address of the memory and show the contents in each of the following: a) MOV [BP]+10,AX b) MOV [SI],AX c) MOV [BX][DI]+20,AX
Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
physcal addresses are 4s ng 4 Ame dat in a cetain compe, te addresses can be translaled without y TLB entries At most how many ditina vid the address translation peh has 12 vld The Translation Look aside Bulfer (TLB)i sine is kB and the word size iby The memory is word addresible. The pe virtual addresses are 64 bea long d th sine is miss?
Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending the required byte, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baud rate delay time Transmit Set up Character Bit Counter • Send Start Bit No Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes • Add Parity if Necessary Send Two Stop Bits Return (a)
. Assume SP=0XE99D, R16=0XE2, R17=0x25, R01=0XFC, R15=0X1F and the following memory information. Address contents (hex) post Address contents (hex) post pre 22 pre 44 OXE996 OXE99C OXE997 46 OXE99D C5 OXE998 17 OXE99E Аб OXE999 21 OXE99F 77 ОхЕ99A F2 OXE9A0 78 OXE99B C3 OXE9A1 A5 Find the values of the registers SP, R01, R16 and R17 after the following operations. РОP R01 РО R16 РОP R17 РOP R20 PUSH R15 SP R16 R17 R01 R20 R15
IF PC= 682 , AR=123 , DR=A2BF, IR= 5672, then execute the following M[AR] DR IR M[AR] Determine the value of IR after the execution and comment on the type of addressing.
Q1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000H to 3009H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending each of the required bytes, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes. The solution must be integrated and include the calculation of the baudrate delay time Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)
An-Najah National University Department of Computer Engineering Microprocessors (10636322) Assignment # 1 Answer the following: 1- Write an 8086-assembly program that reads only vowels (a, e, i, o, u) from the keyboard (other characters are not excepted) and store them in a character array of 10 bytes long. Vowels entered after the array is full should be discarded. The program should stop reading characters when a 'S' is entered. When the 'S' character is entered, the program should output a new line, followed by the contents of the character array, with a space character between each vowel. 2- Write an assembly code to sort a word array of 50 numbers in ascending order. 3- The perfect number is defined as an integer which is equal to the sum of its divisors. Example: 28 is perfect number because 28 = 1+2+4 +7+ 14. Write an inline assembly e function that will takes an integer number as parameter and check whether it is a perfect number or not. Use the function in complete program. 4-…
2. A memory location has a logical address where the segment address is the first four digits is your roll number and the offset address is the last four digits of your roll number. Find the physical address of the memory location. [example: if your roll number is 1234200516789, then the segment address is 1234h and the offset address is 6789h]