Q4: A: Draw only, a distributer (DC ring distributer) ABCDA is fed from point A with 300 v. The main supplies loads are 175 ampere at point B. 322 ampere at point C and 260 ampere at point D. Then put the value and the direction of the current between each two points, if you know that the current (1) between A and B is 335 Amp.

Q4: A: Draw only, a distributer (DC ring distributer) ABCDA is fed from point A with 300 v. The main supplies loads are 175 ampere at point B. 322 ampere at point C and 260 ampere at point D. Then put the value and the direction of the current between each two points, if you know that the current (1) between A and B is 335 Amp.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

What happens to the terminal voltage of the 12.0-V emf with an internal resistance of 0.150 ohm that was originally connected to a 10.00-ohm load and was replaced by a 0.500-ohm load?.
The circuit diagram below shows a generator source supplying three loads through a resistance network. For the values given calculate the voltages at Load A, B, and c. 0.012 ww ww 0.042 ww 0.032 0.062 Load A 120 amp Load B 80 amp Load C 100 amp E-250 Gen 0.060 ww (-) 0.042 0.012 ww 0.032
OCX elp VCC VEE 6V 3V R2 A R1 2kQ 2kQ R5 2kQ a) Find the voltage at point A due to VCC only. b) Find the voltage at point A due to VEE only. c) Find the voltage at point A when both are activated.
Use Kirchhoff's Law to solve for the current passing through each resistor. Compare it with what you got from the PHET Simulation A D 392 www 6V E www F 192 www 292 352 www 9V B C
ii) Given the circuit diagram in Figure 4, find the Vda and Vef voltages. 8 V 12 V 20 V 16 V 8 V 14 V 12 V 4 V Figure 4
Estimate voltage E2 when E1=90sin2400t V, R1=R2=20 ohms, L1= L2=3mH and M=0.15mH
Consider the circuit shown below. Determine the maximum power that can be transferred to the external load RL. Use the following values: R1=9, R2=2 , V=31 V. Report the value with one significant digit after the decimal point. R1 www R2 WHI RL
1a. Calculate the equivalent resistance of R4 and R5 1b. Adding the values of resistor R1 and R2 to R equivalent. Calculate the circuit resistance seen by the power source. 2a. Measure the total resistance across terminals A and D, using ohmmeter function of the electronic VOM. Make sure that switch S1 is in the open position. Measured Total Resistance in Multisim= 4.15kohms 2b. Does the measured total resistance agree exactly with your calculated resistance? Explain
COPY THE ILLUSTRATION BELOW AND IDENTIFY THE BRANCH CURRENT AS STATED. R1 = 12 OHMS R2 = 72 OHMS R3 = 168 OHMS .... .O A solo: 12 72 36
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
The dc load voltage across the load of FIGURE 4 is 91.51V. Compute the value of R1. LOAD R1 R2 Vac k= 20mA 5kohms 220V, IGT= 25mA 60HZ 5.72kohms O 3.21kohms O 1.57kohms
stion 15 2 point Find the branch currents /1 and /2 in the circuit shown in Figure below, by using the Kirchhoffs Current law (KC -). 2 A 5A 4 A 8 A (B) 6A O4A ЗА O 6A and 9A O 1A and 2A hp