Solve the voltage over R₂ and the currents in the circuit. U (= E) = 40V (0 angle), R = R₂ = 15, N L = 6H, L2= 8H, M = 1H Z=jand w= 10Rad/s.I₁ERU LMR₂L₂12ZGive the answers in absolute values (no phase angles).Current I₁, to two decimal places:Current I2, to two decimal places:Voltage over R₂, to one decimal place:AAV

Answered: Image /qna-images/answer/bd42b6c0-3ffc-4111-bbd7-b252f7881efd.jpg

Solve the voltage over R₂ and the currents in the circuit. U (= E) = 40V (0 angle), R = R₂ = 15, L = 6H, L₂= 8H, M = 1H Z=j and w= 10Rad/s. I₁ E R UL M R₂ L₂ 1₂ Z Give the answers in absolute values (no phase angles). Current I₁, to two decimal places: Current I2, to two decimal places: Voltage over R₂, to one decimal place: A V

Solve the voltage over R₂ and the currents in the circuit. U (= E) = 40V (0 angle), R = R₂ = 15, L = 6H, L₂= 8H, M = 1H Z=j and w= 10Rad/s. I₁ E R UL M R₂ L₂ 1₂ Z Give the answers in absolute values (no phase angles). Current I₁, to two decimal places: Current I2, to two decimal places: Voltage over R₂, to one decimal place: A V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.8P: Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor domain.
Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.
In the figure: R1 = 1439.170, R2 = R1 and R3 =2R2, then determine the value of the voltage source E. a 8 mA 10 mA 2 mA RT R1 R2 R3 O 25.33 11.51 O 17.27 15.43 13.82 +
The voltage across a 10uF is shown in the figure below. Determine the current waveform. Showw all steps how you compute the current and draw the corresponding waveform. v(t) (V) 10 15. 10 15 (0 (ms) nere to search Ae
Q4. Determine the equivalent inductance and equivalent current of the inductive circuit in Figure Q4. If L5 is replaced with a capacitor of 0.5 mF, how would it affect the branch current? The alternating Voltage source has an amplitude of 20 Vm. Vm Sine 50 Hz L1 5 mH L2 3 mH Figure Q4 reee L3 6.6 mH L4 2.8 mH rele L5 7 mH
If an electrical circuit draws 100W + J100VAR from a sinusoidal source, then what would the circuit be? Explain why. a) a pure resistor circuit b) a series or parallel R-L circuit c) a series or parallel R-C circuit d) a series L-C circuit
Determine ZT for the circuit if inductive reactive is 10220 and resistance is 9850. Answer:
7. In a pure inductive circuit, the phase angle between the voltage waveform and current waveform will havephase shift * 180 deg O deg 45 deg O 90 deg 8. Why do we say the "voltage across" or "the voltage with respect to?" Why can't we just say voltage? * Voltage is a measure of electric potential difference between two electrical points. O It's an electrical cliche. The other point could be negative or positive. None of the above.
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
The picture shows three LC circuits, two of them with capacitors of capacitance C and the three with coils of inductance L, the three circuits are coupled by means of two capacitors Cc capacitors.L inductance coils, the three circuits are coupled by means of two capacitors of capacitance Cc. The currentscirculating through each mesh are those indicated in the figure: I1, I2 and I3. Using Kirchhoff's law for voltagesand taking into account the definition of current I = -dQ/dt, find the system of coupled equations for the systemand then find the angular normal frequencies of the system.
Figure 2 shows three "LC" circuits, two of them with capacitors of capacitance "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitors "Cc" capacitors. inductance "L", the three circuits are coupled by means of two capacitors of capacitance "Cc". The currents circulating through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = -dQ/dt, find the system of coupled equations of the system and then find the angular normal frequencies of the system.