Q1. A 20m diameter spherical tank is to be used to store gas. The shell plating is 10mm thick and the working stress of the material, that is, the maximum stress to whichthe material should be subjected, is 125 MPa. What is the maximum permissible gaspressure?

Answered: Image /qna-images/answer/66a74323-f55b-45d1-8652-c3b1f19e7fd2.jpg

Answered: Q1. A 20m diameter spherical tank is to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 1. A hydrazine tank, designed by Orbital Propulsion Center, is made of T16A14V STA (3.7164.7) titanium alloy is shown in the figure. a. The length of the tank is 890 mm and its volume is 176.5 liters. Calculate the radius of the tank. b. Determine the tank thickness, t such that the tank resists the proof pressure of 36.9 Bar without permanent deformation and the burst pressure of 49.2 Bar without fracture. c. Under the operational conditions (MEOP), determine the absolute maximum shear stress that occurs on the tank. http://www.space-propulsion.com/spacecraft-propulsion/hydrazine-tanks/index.html Surface Tension Propellant Tank OST 33/0 Net Volume Range 176.5 Litres Propellants Hydrazine (N,H) Spherical with a gylindrical Intersection Geometrical Shape Maximum Expected Operating Pressure (MEOP) 24.63 bar Proof Pressure (1.5 x MEOP) 36.95 bar Burst Pressure (2.0 x MEOP) 49.26 bar Interface Fixation 4 Suspension Trunnions Materials - Pressure Vessel TIGAIAV STA (3.7164.7) -…
Mechanical Engineering. Need solution for this problem. Thanks A 15-lb block of brass with a specific heat of 0.089 is heated to 189°F and thenimmersed in 5 gal of water at 66°F. What is the final temperature of the brass andwater? Assume there is no heat loss.
Q A thick-walled cylinder has an inside diameter of 150mm. The inside of the cylinder is subjected to an internal fluid pressure of 350bar and the external pressure being zero. The fluid has a nominal density of 785kgm-3 and a viscosity of 36mPas. a) Find to the nearest mm the outside diameter required if the maximum stress of the material is 400 MNm-2 and a safety factor of 3 is required. b) Plot the stress distributions through the wall.
A Midwest Cooperative needs to store 15 750 gallons of a liquid chemical. They are considering two possible containers, a hollow cylinder or a hollow sphere. The wall of the sphere will need to be 6 in. thick and the wall, top and bottom of the cylinder are each 6 in. thick. Due to space limitations the height of the cylinder must be 26.0 ft. (a)What will be the outside diameter of the cylinder required to hold the liquid chemical? (b)What will be the outside diameter of the sphere? (c)Assume the containers are made of aluminum, which container uses the most material?
Please show the complete solution including FBD.
A thin-walled cylinder shell has an internal diameter of 2m, is fabricated from plates 20mm thick. 1.)Which if the following gives the safe pressure in the shell if the tensile strength of the plate is 400 MPa and the factor of safety is 6? 2.) Which of the following gives the ratio of the hoop stress over the longitudinal stress of the cylinder? 3.) Which if the following gives the required wall thickness of the cylinder if this tank consists of a cylinder closed by hemispherical ends and subjected to an internal pressure of 2.0 MPa ?
By measuring the pressure inside a balloon that is slowly inflated until it bursts, it should be possible to estimate the maximum tensile strength of the balloon material. A balloon bursts when it reaches 20cm at a pressure of 2atm. What is the tensile strength (maximum tangential stress) of the material given that the balloon was 1mm thick?
A spherical tank for storing gas under pressure is 25m in diameter and made of steel 15mm thick. The yieldpoint of the material is 240MPa. What is the maximum permissible internal pressure?
a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa
What is the strain in an axis-symmetric, unconstrained, thin-walled pressure vessel?
Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at apressure of 5.75 MN/m2 . The diameter of the vessel is 400 mm, and the stress is limited to28.75 MPa.
Example 1.12. A vertical cylinder of diameter 180 mm rotates concentrically inside another cylinder of diameter 181.2 mm. Both the cylinders are 300 mm high. The space between the cylinders is filled with a liquid whose viscosity is unknown. Determine the viscosity of the fluid if a torque of 20 Nm is required to rotate the inner cylinder at 120 r.p.m. Liquid 0.6 mm Outer cylinder Inner rotating cylinder -180 mm dia. 181.2 mm dia. 300 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q1. A 20m diameter spherical tank is to be used to store gas. The shell plating is 10 mm thick and the working stress of the material, that is, the maximum stress to which the material should be subjected, is 125 MPa. What is the maximum permissible gas pressure?