Q) A shaft 1.5 m long are supported in flexible bearings at the ends and carry two wheels each of 50 kg mass. One wheel is situated at the center of the shaft and the other at a distance of 0.4 m from the center towards right. The shaft is hollow of external diameter 75 mm and inner diameter 37.5 mm. The density of the shaft material is 8000 kg/m3. The Young's modulus for the shaft material is 200 GN/m2. Find the frequency of transverse vibration.

Q) A shaft 1.5 m long are supported in flexible bearings at the ends and carry two wheels each of 50 kg mass. One wheel is situated at the center of the shaft and the other at a distance of 0.4 m from the center towards right. The shaft is hollow of external diameter 75 mm and inner diameter 37.5 mm. The density of the shaft material is 8000 kg/m3. The Young's modulus for the shaft material is 200 GN/m2. Find the frequency of transverse vibration.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft 1.5 m long is supported in flexible bearings at the ends and carries two wheels each of 50 kg mass. One wheel is situated at the centre of the shaft and the other at a distance of 0.4 m from the centre towards right. The shaft is hollow of external diameter 75 mm and inner diameter 37.5 mm. The density of the shaft material is 8000 kg/m3. The Young’s modulus for the shaft material is 200 GN/m2. Find the frequency of transverse vibration.
Three uniform disks made up of two same materials with one being lighter compared to the other material. The inner half of the disk 2 is made up of the denser material while for the other two disks it makes the outer half. Tangential forces of equal magnitude are applied either on the interface of inner and outer half or on the outer edge. Write the disk numbers from highest to lowest according to:(a) the torque about the disk center(b) the rotational inertia about the disk center(c) the angular acceleration of the disk
4- Determine the required diameter of the solid shaft BC, if the allowable shearing stress is given as 70 MPa 5- Sketch the distribution of the shear stress due to torsion in shaft BC. 6- Make a simple sketch to show the distribution of the angular deflection due to torsion in shaft BC.
A shaft is made from solid material of density 7800 kg/m and E= 210 GN/m? to be applied for this question. a) The shaft of 15mm diameter is to be supported in self-aligning bearings. If the shaft is required to rotate at 7000 rev-min determine the greatest distance of unsupported length if the shaft is not to whirl. b) The shaft of 12 mm diameter is supported in 'long' bearings at both ends, which are 0.6m apart. i) Determine the first three whirling speeds for the shaft. ii) In order to provide additional stability to the shaft by fitting a 'short' self-aligning bearing at mid-span of the shaft, show that this will shift the first whirling speed to be effectively the same as the second whirling speed, without the mid-bearing.
Hollow steel shaft of 100 mm as internal diameter and 150 mm asexternal diameter is to be replaced by a solid alloy shaft. If the polarmodulus has the same value for both, determine the diameter of thesolid shaft.
A shaft having length equal to 10 m and diameter equal to (50+ 01) mm is simply supported at both ends. The shatt carries four masses (150 + 01) kg, (200 + 01) kg, (250 +01) kg and (300 + 01) kg. These masses are located at a distance of 1.5m, 2.5 m, 5.5 mand 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m? and mass density for the shaft material is 7500 kg/m?3. Determine critical speed of the shaft in revolutions per minute for the following two cases: 1. Effect of the mass of the shaft is neglected. 2. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
This airplane nose wheel assembly is raised by applying a torque M, as shown. The arm AD and the wheel have a combined weight of 100lbs, and the center of gravity is at G, as shown. Determine the torque required to maintain the assembly at the configuration shown in the following figure (D is directly below B and ?= 15°). 16" B M 20" 32" 20"
A shaft is supported in two bearings 2.8 m apart and projects 0.7m beyond the bearings at each end. The shaft carries three pulleys, one at each end and one at the middle of its length. The end pulleys have masses of 95 kg and 60 kg and their centres of mass are at 3,65 and 6 mm respectively from the shaft axis. The centre pulley has a mass of 82 kg and its centre of mass is 6.05 mm from the shaft axis. If the pulleys are arranged so as to give static balance, determine the dynamic forces produced on the bearings when the shaft retates at 350 r/min
Finding the value of sectional modulus of shaft having diameter 3 m
The tapered circular steel shaft is attached to a hollow circular steel shaft. Compute the angle of rotation (in degrees). Use G = 83 GPa
A machine part as shown in following figure consists of three disks linked by light weight struts. Use mA=0.62 kg, mB=0.98 kg, mC=0.2kg, a=0.78m, b=0.21m and c=0.807774721m. a. What is this body's moment of inertia in kg/m2 about an axis through the center of disk A, perpendicular to the plane of the diagram? Insert your answer correct up to at least a third decimal place. b. What is the moment of inertia in kg/m2 about an axis through the centers of disk B and C? Insert your answer correct up to at least a third decimal place. c. What is the body's kinetic energy in Joule if it rotates about the axis through A with angular speed ω=32 rad/s? Insert your answer correct up to at least a third decimal place.
This airplane nose wheel assembly is raised by applying a torque M, as shown. The arm AD and the wheel have a combined weight of 100lbs, and the center of gravity is at G, as shown. Determine the torque required to maintain the assembly at the configuration shown in the following figure (D is directly below B and ?= 15°).