A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force FB at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum slope specification of 0.062° for good bearing life. Check wether the shaft dia below meets the requirement. If not determine a suitable shaft diameter.

A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force FB at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum slope specification of 0.062° for good bearing life. Check wether the shaft dia below meets the requirement. If not determine a suitable shaft diameter.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The value of curvature correction factor k, will be if the spring index is 6. O a. 1.33 O b. 1.08 O c. 0.92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is N, Take pressure angle as 14½0. at Pitch P. point Gear driven to 02 The radial force is
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Figure. The shaft is mounted on two bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 (ou = 750 N/mm?). The factors kp and k; of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 400 400 270 250, 640 210 640 100
A gear-reduction unit uses the countershaft depicted in the figure. Find the two bearing reactions.The bearings are to be angular-contact ball bearings, having a desired life of 60 kh when used at 330 rev/min. Use 1.2 for the application factor and a reliability goal for the bearing pair of 0.92
A bevel gear receives a power from bevel pinion results in the shown forces. The forces are F = 7026.8 i - 3513.4j+ 215840.8 k . the bevel gear average diameter is 210 mm. the shaft is supported at bearing E and F and delivers the power to a flange coupling at end G. the shaft is made of steel 826 M 40 H&T having Sy = 650 MPa and Sult = 850 MPa. Determine the shaft diameter at its critical section and make a complete construction drawing. Fr= 3513.4 N F, = 7026.8 N. F= 21584.8 N 100 mm 200 mm 105 mm
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 400 The shaft is mounted on two 400 400 270 250 ]640 210 640 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 100
Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm diameter solod shaft supported by the bearings is to be made of machined AISI 1045 CD steel. The helical gear is subjected to the axial force F-498 y a radial load F- 750 N and a tangential load of F-1.995 N. Assume the component is g at room temperature of 70F and the material has s0s reliability factor. Hint: Be careful when you calculate the bending moment at the fillet, as all the three forces on the helical gear cause bending moment at the fillet. Calculate resultant bedina moment from all the three forces. Bending moment is completely reversed loading.) 25-mm solid round shaft Fillet Bending K, = 2.0 Torsional k, = 1.5 Axial K,18 F. F, F Pump Helical spur gear -50 mm -250-mm dia FIGURE 1. Identify the critical locations) of stress and show it clearly in a diagram. 2 Identity cleary, all the components of stresses (at the critical point) that will be calcurated (by drawing and clearty…
Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm diameter solod shaft supported by the bearings is to be made of machined AISI 1045 CD steel. The helical gear is subjected to the axial force F =499 y a radial load F = 741 N and a tangential load of F=2,006 N. Assume the component is operating at room temperature of 70°F and the material has 50% reliability factor. 25-mm solid Bending K, = 2.0 round shaft Fillet Torsional K = 1.5 F. F, Axial K, = 1.8 F Pump Helical spur gear 50 mm -250-mm dia.- FIGURE 1. Identify the critical location(s) of stress and show it clearly in a diagram. 2. Identify cleary, all the components of stresses (at the critical point) that will be calculated (by drawing and clearly showing the XYZ axes) and show it in a matrix form. Show which components of stresses will have a value zero or non-zero. 3. Calculate the principal stresses and principal directions. Show the principal stresses clearly in a stress element…
4. A machine shaft turning at 600 rpm is supported on bearings 30" apart. Twenty HP is supplied to the shaft through an 18" pulley located 10" to the right of the right bearing. The power is transmitted from the shaft through an 8" spur gear located 10" to the right of the left bearing. The pulley weighs 200 lb to provide some flywheel effect. The forces acting on the pulley and the gear are given in the diagram. The shaft material selected has an ultimate strength of 70,000 psi and a yield stress of 46,000 psi, determine: Reactions at the bearings b. Bending moment diagrams in the horizontal and vertical directions a. The necessary diameter in accordance with the ASME Code using Kh=1.5 and Kt = 1.0. points) с. Pulley Mt 525 lb Gear 191 lb Mt Forces on Gear 10" 20" 10" 348 lb W-200 lb 116 lb
Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angleare in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh.The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at eachpair assuming equal direction of load between the pairs. Neglect friction.
The figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an 18-tooth 20° pinion driving a 45-tooth gear. The power input is 28-hp at 1700 rev/min. Find the magnitude of the force acting on bearing D. 3 2 3 in 3 in The magnitude of the force acting on bearing Dis lbf.
13-55 Gear 2, in the figure, has 16 teeth, a 20° transverse pressure angle, a 15° helix angle, and a module of 4 mm. Gear 2 drives the idler on shaft b, which has 36 teeth. The driven gear on shaft c has 28 teeth. If the driver rotates at 1600 rev/min and transmits 6 kW, find the radial and thrust load on each shaft. LH 90° Problem 13-55 RH RH
A 50 mm transmission shaft transmitting 15 kW power at 200 rpm is supported on two deep grove ball bearings 750 mm apart and two gears are key to it. The pinion and gear have 30 and 100 teeth respectively. The pinion is located at 100 mm to the left of the right bearing, whereas the gear is located at 150 mm to the right of the left bearing The module and pressure angle of gear is 5 and 20o involute. Pinion delivers power horizontally to the right and gear received power in a vertical direction from below as shown in Figure l. The expected life of 15,00 h assumes the torque is the same for both pinion and gear and the bearings are under radial load only. Find the pitch diameters of pinion and gear. The torque transmits by the shaft Find force FC and FD Select suitable deep groove ball bearings at A and B B 150 500 100 Fe N-