Problem 1. P 3 m D 3 m B E 3 m A F -7m-| For the frame shown with P = 87 N, determine the forces at the support A and at the pin C. Find all the forces with 2 SigFigs and enter your answer putting them together as follows: • Ax = aa • Ay = bb • Cx = cc Cy = dd Enter your answer as aabbccdd, removing signs, decimal points and units

Problem 1. P 3 m D 3 m B E 3 m A F -7m-| For the frame shown with P = 87 N, determine the forces at the support A and at the pin C. Find all the forces with 2 SigFigs and enter your answer putting them together as follows: • Ax = aa • Ay = bb • Cx = cc Cy = dd Enter your answer as aabbccdd, removing signs, decimal points and units

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.22P: A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo...

See similar textbooks

Similar questions

GIVEN: DISTANCES CO= 7m BO= 7m OD= 8m AD= 8m GIVEN: WEIGHT W1= 195 N W2= 295 N GIVEN: ANGLE X= 55 Degree Y= 48 Degree SOLVE: (a) Tension at CB in NEWTON (b) Reaction at point O in NEWTON PLS PLS SOLVE AND SHOW COMPLETE SOLUTION AND WRITE LEGIBLY. ALSO, DRAW THE FREE-BODY DIAGRAM. ROUND OFF IN 4 DECIMAL PLACES.
RAY B F F₁ ROY
ENTER YOUR ANSWER THE WAY I SPECIFY HERE IN ADDITION TO DOING IT ON SCRATCH PAPER 400 N 800 N B D A E C 2 m Use the method of sections to calculate the axial force in members AC and BC. Enter your answer in the following way rounded to the nearest whole number. Example If your answer is TAC 2 N tension TBC =3.1 N compression. enter 2Tension;3Compression Enter TAC then TBC (no space)
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. 1.) Determine x-component of vector DF. 2.) Determine the y-component of Vector DF 3.) Determine the z-component of Vector DF. 4.) Determine the moment experienced by the system assuming that there is no wire support.
OP •C h W The man in the diagram is trying to move a large box by pushing on it with a force, P. The box weighs 300 N and its centre of gravity is located in the centre of the box (point C). Given: a = 1.8 m b = 0.8 m h= 0.9 m What is the minimum force that will cause the box to tip? Please include the unit ("N") within your answer and round to 3 significant figures (e.g. if the calculated answer was 55.562 Newtons please input: 55.6 N). Answer: What is the minimum coefficient of static friction that will permit tipping to occur? Please do not include the unit s (as there are none) within your answer and round to 3 significant figures (e.g. if the calculated answer was 55.562 please input: 55.6). Answer:
6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in
4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.
The beam is supported by a fixed support at point A. There are 2 distributed loads applied to the beam. Neglect the weight and thickness of the beam. Take the origin for all functions to be at A. , i.e. start at the left and go right. Must use positive sign convention for V and M. W1 A W2 d1 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value di 3 m W1 6 (kN)/m W2 3 (kN)/m a. For the interval 0 < x < 3 m, determine the equation for the Shear Force as a function of x, V(x). b. For the interval 0 < x < 3 m, Use integrals to determine the equation for the Moment as a function of X, M(x). o Enter the coefficient of the x term as a fraction and the rest as decimals. for example, x4 1.4x c. Determine the magnitude of the max shear on the beam,Vmax d. Determine the magnitude of the max bending moment on the beam, Mn max
Help Save & Exit Check Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L= 8 ft and F= 12 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B 30° F T AB : the position vector from A to B. TAB of 17 Next > < Prev 6. 9. 41
ASAP
Please help. Please make sure you clearly state how you got the numbers you got and why you are using them. Also please make sure you clearly put your formulas and label your units along the numbers that you are using. In the following frame ilustration, F1s 60 N and F2 is 9 N. What is the tension in the cable AB and the reaction force vector necessary to keep the system in static equilibrium? Give the X component reaction force at C( for an x axis going left to right). Also please solve for the rest of the 3 unknowns please. Thank you
9 - In the cage system connection in the figure; Rod forcesS1 = 100 kN,S2 = 40 kN,S3 = - 60 kN,S4 = 50 kN,If S5 = 80 kN, Calculate the resultant force acting on joint D.If the vector representation of the resultant force is R = Rx i + Ry j, Ry =? Note: The (-) sign of the bar force S3 indicates that the force is pressure. A) 12.93B) 3.64C) -36.36D) 27,07E) -12.93