odified book exercise: Vector Mechanics for Engineers: Statics and Dynamics (8th Edition) chapter 4 and exercise 12 Four boxes are placed on a 17,7 kg uniform wooden plank that rests on two trestles. Knowing that the masses of boxes B and D are 2.5 kg and 32 kg, determine, respectively, the range of values for the mass of box A so that the plate remains in equilibrium when box C is removed

odified book exercise: Vector Mechanics for Engineers: Statics and Dynamics (8th Edition) chapter 4 and exercise 12 Four boxes are placed on a 17,7 kg uniform wooden plank that rests on two trestles. Knowing that the masses of boxes B and D are 2.5 kg and 32 kg, determine, respectively, the range of values for the mass of box A so that the plate remains in equilibrium when box C is removed

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.8.4P: Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE=...

See similar textbooks

Similar questions

3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive force of 8 kips. The 1.5-in side changed its length to 1.50014 inches. Use E = 10 x 10³ ksi. Calculate the new length of the 2-inch side. Answer: Lnew = 2.00019 in 1.5 in 2 in. 8 kip- 8 kip 3 in. 4. A solid cylinder of diameter D is subjected to an axial load P. Show that its change in diameter is 8D = 4Pv/лDE.
101 10- R = ? -2m- F3= 15 KN F₂ = 12 kN F₁ = 10 kN -3 m Fig. P2-58 2 4 m 2 m y
a=2.1m (1) c = 2m b = 3.1m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES B dia. of rod 1: = 13mm dia of rod 2 = 11 mm
8&N 25 kN-m 5 kN Fig (1)
10/10 find the tensile stress in upper plate in section 3-3 5. 1 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 2) 300 mm 8 mm
-8 in.- -8 in.- (a) (b) Which of the following best explains why cylinder (b) has a higher longitudinal stress in its walls compared to cylinder (a)? Assume the gauge pressure of the fluid inside the cylinder is non-zero. O Cylinder (b) is supported at two locations Cylinder (a) is not free to deform in its longitudinal direction The vertical (longitudinal) pressure in cylinder (a) is transferred directly to the [bottom] support, bypassing the cylinder walls None of the above the longitudinal stress for both cylinders is the same
Question 38 What is the total length of bar mark 01 Use S1 - 250 mm. Size of column is 300 x 300 mm 02 01 6.2 m 02 LJ4 S1 L/2 THE 03 -Column -04 L = 5m SUPPORT MIDSPAN 4mm 250 mm 250 m OF 120 mm 40 n 120m 400 0-10 mn dn, 10 rm da stimups 2 58,4 100, rest 200 n S10mn dia, 10 mm di srups 2a 5a, 100, est 200 mn O B840 mm O NONE DF THE CHICES O 13240 nm O 2500 mm
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
Consider a long cylindrical solid rod - total length L - mass density p; - radius R1 = R2 = R; suspended from the top and hung freely downward along the (-1)Ž direction; - subjected to gravitational pull from the ground in the (-1)Ź direction. R2 +Z Z = h R1 Z = 0 a) Calculate the longitudinal stress o within the rod as a function of h; b) Repeat the calculation ifR| turns into a cone); = 0 and R2 = R (i.e., when the cylindrical rod c) Based on your answers to a) and b), provide some reasoning as to why a space elevator would not work [hint: think about the rod as the load bearing element of the space elevator].
b=3.1m a=2.1m (1) B C = 2m P = 80kN C d = 1.8m WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES dia of rod 1 = 13mm dia of rod 2 = 11 mm
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring