Take that wo = 5.0 kN/m (Figure 1) Figure 500 kN-m Part A FR = Submit ON Part B. μA Replace the loading by a single résultant force and determine its magnitude. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. Value 7.5 m Units Previous Answers Request Answer μÀ Wo X Incorrect; Try Again; 5 attempts remaining d= Value Units ? Submit Previous Answers Request Answer 4 Specify the location of the resultant force measured from point O. Assume that the location of the equivalent resultant force is not necessary on the beam. Express your answer to three significant figures and include the appropriate units. ? 4.5 m 1 of 1 * Incorrect; Try Again; 5 attempts remaining 15 kN >

Take that wo = 5.0 kN/m (Figure 1) Figure 500 kN-m Part A FR = Submit ON Part B. μA Replace the loading by a single résultant force and determine its magnitude. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. Value 7.5 m Units Previous Answers Request Answer μÀ Wo X Incorrect; Try Again; 5 attempts remaining d= Value Units ? Submit Previous Answers Request Answer 4 Specify the location of the resultant force measured from point O. Assume that the location of the equivalent resultant force is not necessary on the beam. Express your answer to three significant figures and include the appropriate units. ? 4.5 m 1 of 1 * Incorrect; Try Again; 5 attempts remaining 15 kN >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the ox value for the plate as shown below, where b1=d2%=D16 mm, d1=70 mm,b2%=90mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1
> shown. The distributed load acts on the shaft as shown. Suppose that a = 0.7 ft. (Figure 1) Figure w = (2x - 8x + 18) lb/ft 10 lb/ft 201 -2 ft 1 of 1 18 lb/ft B ▼ Determine the magnitude of the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR = Submit Part B 0 d= μÀ Value Request Answer h μA Specify the location of the resultant force, measured from the support A. Express your answer to three significant figures and include the appropriate units. Value Units P Pearson PSMK ? Units SAM ?
The stress state within the lateral wall of a soda can is approximated as shown. p is the internal pressure, r is the radius of the can, t is the wall thickness. Express the stress state shown in a matrix, where the only two non-zero stress components are σxx and σyy, all other stress compoenents are zero. Express the equivalent stress σe associated with the stress state shown in terms of p, r, and t.
Examples IF 6 = 60 8 T:5 KN, determine the magnitude of the resultunt force on the eye bott aud it's direetion measured cockwise from the positive l-atis acting )45 SKN
The beam is supported by rods AB and CD that have different cross-sectional areas. The area of rod AB is AAB = 10 mm² .The area of rod CD is Acp = 8.25 mm². B F₁ Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F₁ d₁ d₂ NAB= 5050 N 3.25 mm 0.5 mm a. Determine the magnitude of the normal internal force in rod CD, NCD. b. Determine the magnitude of the normal internal force in rod AB, NAB. c. Determine the normal stress in rod CD, OCD. d. Determine the normal stress in rod AB, O AB. Round your final answers to 3 significant digits/figures. NCD = N N
Replace the loading on the beam by an equivalent resultant force. (Figure 1) Suppose that w₁ = 3.0 kN/m, w2 = 0.6 kN/m, and F = 1.8 kN. Figure WI 3 m W2 1m < 1 of 1 Part A Determine the magnitude of the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR = 5.49 Submit Part B d = X Incorrect; Try Again; 3 attempts remaining 0 Submit µÅ Specify the location of the equivalent resultant force, measured from point A. Express your answer to three significant figures and include the appropriate units. Previous Answers Request Answer Value Provide Feedback kN O μA Request Answer ? Units ?
Calcuate Bending From Point A to Point B and Point A to Point C, Calcuate torsion From Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cm
Problem 7.30 - Enhanced with Hints and Feedback In (Figure 1), F = 810 lb. Follow the sign convention. Figure 800 lb علام 1.5 ft 1.5 ft 300 3ft F 30° 1 of 1 600 lb 3 ft Part A Determine the normal force acting at point D. Express your answer in pounds to three significant figures. ND = Submit Part B VD = IVE ΑΣΦ ↓↑ vec Determine the shear force acting at point D. Express your answer in pounds to three significant figures. Submit Request Answer πVE ΑΣΦ | 11 Request Answer vec ? ? lb lb 4 of
A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was 10 N. The thickness of the metal is twice its L. Using the formula on the three-point test of materials, compute for the thickness of the metal in centimeters.
When the two forces are placed on the beam, the diameter of the A-36 steel rod BC decreases from 40 mm to 39.96 mm. (Figure 1) Figure -1 m -1 m P -1 m- B 0.75 m 1 m Part A Determine the magnitude of each force P. Express your answer to three significant figures and include the appropriate units. P = μA Value KN Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 2 attempts remaining
The state of stress at a point on an element of material is shown. Let sigmaX= 49.0 ksi, sigmaY= 17.0 ksi, and Txy= 11.0 ksi. Use this information to represent the principle state of stress and maximum in plane shear stress. Plot the mohr circle and state sigmaX' and sigmaY' and Tx'y' with unit. Also draw the state of stress on the rotated element.