shown The distributed load acts on the shaft as shown. Suppose that a = 0.7 ft. (Figure 1) Figure -w-(2x²8x + 18) lb/ft 10 lb/t 20 2 ft <1 of 1 18 lb/ft V Determine the magnitude of the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR= Submit Part B μA 3 Value TALES I Request Answer → Units ? Specify the location of the resultant force, measured from the support A. Express your answer to three significant figures and include the appropriate units. G → C SHINE ?

shown The distributed load acts on the shaft as shown. Suppose that a = 0.7 ft. (Figure 1) Figure -w-(2x²8x + 18) lb/ft 10 lb/t 20 2 ft <1 of 1 18 lb/ft V Determine the magnitude of the equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR= Submit Part B μA 3 Value TALES I Request Answer → Units ? Specify the location of the resultant force, measured from the support A. Express your answer to three significant figures and include the appropriate units. G → C SHINE ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

novig size modestib Beri N 1-12 12- 60° 37. A block-and-tackle pulley hoist is suspended in a warehouse ay by ropes of lengths 2 m and 3 m. The hoist weighs 350 N. The ropes, fastened at different heights, make angles of 50° and th 38° with the horizontal. Find the tension in each rope and the magnitude of each tension. 50° brd 60° 2 m 38° 3 m 501001 hon sit 44. 45 4
Please write the final answer with unit 3.Length and diameter of a bearing are equal (d=L). This bearing should be able to withstand the allowable support force of 80 N. Allowable support tension is 20 N/cm?. Determine the length of bearing.
Q' Compute the magnitude F of the force which the earth exerts on the moon, Perform the calculation in Newtons. Hint: Please use : F - G" G= 6.673 10" m'kg.s m-5.976 10 kg m-6.673*10" kg -384398*10' m
1 0 Calculate the total volume of the cylindrical component below (not to scale): L1 D1- D1 = 1.12 cm D2 = 0.71 cm D3 = 1.58 cm L1 = 18.68 cm L2 = 15.36 cm L3=13.77 cm L4 = 9.77 cm Answer: Check L2 L3 L4 D2- What is the volume of the cylindrical component? (State your answer in S.I. units (m³), accurate to 3 significant figures) D3
(200 lb)(0.6 ft)+PABcos30°(0.75 ft)PAB==0184.752 lb Can you please show all the numbers in this equation so that it would be clear how you get the 184.752 lb in the end.
GIVEN: W= 595 N GIVEN: ANGLE A= 44 DEGREE GIVEN: ANGLE B= 14 DEGREE ANSWER: SOLVE (A) IN UNIT CM SOLVE (B) IN UNIT N-CM SOLVE (C) IN N-CM PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY AND SHOW THE FREE BODY THE DIAGRAM PLS TAKE NOTE OF THE UNITS WHICH ARE IN CM NOT IN MM AND ALSO LOOK AT WHAT SHOULD BE THE UNITS IN SOLVING (A) IN UNIT CM IN (B) IN UNIT N-CM AND IN (C) IN N-CM.
The lace Facts on the bracket within the octant shown in Fig.1) Figure Part A HF-520 N-65 and y 45", determine the zy z components of F Enter the components of the force separated by commas. Express your answers in newtons to three significant figures Az ivec 0 F. P. F. Submit Provide Feedback Request Answer ? N
200 LB z00 LB 200 LB 200 LB 200 UB 200 LB 20003 D 00 LB 00 LB 30° 30 60' SOLVE FOR THE FORCES IN MEMBETRS HF, GH, AND EK. INDICATE F COMPRESSION or TENSION.
The cable supports a railway bridge between two tunnels. Given: Distributed load, w = 1.01 MN/m Allowable cable tension, Talllow = 47.2 MN. Distance, a = 21 m a a What is the corresponding value of "h" in meters? Express your answer in 1 decimal place. 3
1. Note: for part a), you can do this without a calculator; it might be easier to work out the problem symbolically, and then substitute the numbers at the end of the problem. В 2L The axial rod is fixed to the two walls, as shown above. Portion AB is composed of one material (EAB = E), while portion BD is composed of a different material (EBD = 2E). Portion AB has cross sectional area AAB = A, while portion BD has cross sectional area ABD = 2A. EAB = E = 15×106 psi AAB = A = 1 in² EBD = 2E = 30×10° psi ABD = 2A = 2 in² LAB = L = 10 in. LBC = 2L = 20 in. LcD = L = 10 in. An external force, P = 100 kips, is applied at point C as shown below. a) Determine the reaction forces at wall A and D, Ra and Rp. Specify the direction, (→) or (+). b) Deflection at point C. Specify the direction, (→) or (+). (Ans: RA = 100/7 kips →, Rp = 600/7 kips →, & = 1.429x10² in –)
pivot X 30° F As shown in the diagram above (viewed from above), force F of magnitude 882 N is exerted on a rod which is pivoted about its center a distance 0.7 from the pivot. Calculate the torque exerted by force F. Express your answer in N*m and round to the nearest tenth (1 decimal). Enter a negative answer for a clockwise torque and a positive answer for a counterclockwise torque.
p1= 1780 N p2 = 1570 N p3 = 1340 N