Make an illustration for this problem and label it completely. This lever has a fulcrum that they will balance from the middle of the beam. There were 5 boxes on this beam and it had a total weight of 2,158 pound and had a length on each side of 10 feet from the middle. The Package A weighs 360 pounds and it is located at the right Most Part of the lever and its CG was located 5 inches from the edge. The Package B weighs 400 pounds and its CG was located 115 inches from package A and going to the middle of the beam. Package C weighs 400 pounds and its arm measured 70 inches from the right of datum. Package E was placed accordingly to balance this lever because the package D was situated opposite from package A and with 60 pounds difference. Complete the needed value on this balance beam.

Make an illustration for this problem and label it completely. This lever has a fulcrum that they will balance from the middle of the beam. There were 5 boxes on this beam and it had a total weight of 2,158 pound and had a length on each side of 10 feet from the middle. The Package A weighs 360 pounds and it is located at the right Most Part of the lever and its CG was located 5 inches from the edge. The Package B weighs 400 pounds and its CG was located 115 inches from package A and going to the middle of the beam. Package C weighs 400 pounds and its arm measured 70 inches from the right of datum. Package E was placed accordingly to balance this lever because the package D was situated opposite from package A and with 60 pounds difference. Complete the needed value on this balance beam.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

solve and show detailed solution with diagram
Identify the valvetrain components in the drawings. Place the identifying letter next to the name of the component. B -N Valve Port Guide Valve Head A Stem Valve Seat Keeper Groove C- Margin Stem Tip EFace D- Pushrod 6. トリ E- tifter Spring F- Valve Rocker Arm ーKu Cam Lobe H-
Q3 / Draw the following spring with all dimensions in sheet (write down all the equations you used in the :drawing if found) D1 70 mm D2 50 mm L 125 mm d 10 mm Pitch 25 mm
I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal places for magnitude. DO NOT FORGET YOUR UNITS. Enclose all final answers in a box. No need to copy the question or problem. File submissions should be a single PDF. II. PROBLEM SOLVING 1) Given the figures and data below, solve what is being asked for. Y-axis 200mm -200mm 50mm 50mm 100mm 200mm 100mm Y-axis Yo 200mm 100mm 3°1 100mm 547 - ATT HA LO - CHIR →→X-axis -Xo →X-axis
Please use equations attached
Please solve 1 to 4 please ??
Solve question 2-4*
Page 6 of a Another name for "SIZE DESCRIPTION" is: A Dimensioning. B Orthographic projection. C Assembly drawing. D Pictorial drawing What is the length to width ratio of arrowheads? A 1:1 37 42 в 2:1 С 3:1 D 5:1 Leader lines should NOT be drawn: 38 "2X on a hole note means: 43 A At 45°. A Double the size of the hole. B At 30°. C At 60°. D Horizontally or Vertically. B Reduce the stated size by 1/2. C The scale of the hole is doubled. D There are two boles the same size. Extension lines are drawn: 39 Avoid dimensioning to: 44 A Extremely thick, A Hidden lines. B Thick. B Center lines, C Thin. D Extremely light. C Extension lines. D Holes. What is the standard length for arrowheads? CIRCLE SIZE is specified by: 45 40 A 031 (.5mm) B 063 (Imm) A Chord. B Circumference. C Diameter. C. 125 (3mm) D 250 (6mm) D Radius. Dimension lines should be: 41 46 The size of an ARC is typically specified by its: A Thick and dark. A Diameter, B Thick and light. B Circumference. C Chord. C Thin and dark.…
solve show all steps and solutions for a-c
Solve part 4 only
Pls i need the counting of link and j1 and j2 with count on graph
Can someone please help me to solve this and draw using autoCAD as well as show all work for part B.