please help with this question It is important to pre-wet the filter paper before filtering your sample. Which statements about this step of the procedure are true? More than one answer may be correct.Always use distilled water to pre-wet the filter paper.Pre-wetting helps to hold the paper in place against the bottom of the funnel.Sufficient solvent should be used to just wet all parts of the filter paper.Use a small amount of clean solvent, which is the same as the solvent used in the reaction.O Wetting the paper helps dissolve any unwanted solid impurities.Submit AnswerTry Another Version1 item attempt remaining

One important step in the procedure for filtration using filter paper is to pre-wet the filter paper…

It is important to pre-wet the filter paper before filtering your sample. Which statements about this step of the procedure are true? More than one answer may be correct. | Always use distilled water to pre-wet the filter paper. O Pre-wetting helps to hold the paper in place against the bottom of the funnel. O Sufficient solvent should be used to just wet all parts of the filter paper. O Use a small amount of clean solvent, which is the same as the solvent used in the reaction. O Wetting the paper helps dissolve any unwanted solid impurities. Submit Answer Try Another Version 1 item attempt remaining

It is important to pre-wet the filter paper before filtering your sample. Which statements about this step of the procedure are true? More than one answer may be correct. | Always use distilled water to pre-wet the filter paper. O Pre-wetting helps to hold the paper in place against the bottom of the funnel. O Sufficient solvent should be used to just wet all parts of the filter paper. O Use a small amount of clean solvent, which is the same as the solvent used in the reaction. O Wetting the paper helps dissolve any unwanted solid impurities. Submit Answer Try Another Version 1 item attempt remaining

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter13: The Chemistry Of Solutes And Solutions

Section: Chapter Questions

Problem 83QRT

See similar textbooks

Similar questions

How do you determine how much solvent to add during recrystallization? What happens if you add too much? Too little?
A supporting electrolyte is usually added to the analyte solution to minimize solution resistance.minimize solution conductivity.make the analyte less soluble in solution.increase the scan rate.
Which one answer does NOT represent a characteristic of a good recrystallizing solvent? O 1) Should not react with sample. O 2) Should do a poor job of dissolving impurities when hot. O 3) Should have a moderate boiling point. O 4) Should do a good job dissolving a sample when cold.
What is the retention factor (Rf) of the most polar and least polar spot present in the standard ink? (Use 2 significant figures)
Just prior to drying an organic layer with a drying agent, you notice water droplets in the organic layer. What should you do next? Double the amount of drying agent used. O Transfer the organic layer to a clean flask before adding any drying agent. Stir or swirl with solution with the drying agent well. Double the drying period and let the solution dry for 30 minutes.
10 mL of 10 % sodium sulphate solution into a clean test tube. Add 1 drop of 10 % barium chloride. What do you observe? Write an equation to explain your observations in your lab report. C2. Measure out a fresh 10 mL portion of 10 % sodium sulphate into another test tube. Making sure to count the drops, use a dropper to add 30 % calcium chloride solution. Swirl the solution after each drop. Continue until a white precipitate occurs. Write an equation to explain your observations. Which solubility product has the smaller numerical value, that for calcium sulphate or barium sulphate? Explain how you know this is true. C3. Measure out another 10 mL portion of 10 % sodium sulphate into a clean test tube. Add 8 drops of 50 % sulphuric acid and swirl. Count the number of drops (swirl after each drop) of 30 % calcium chloride needed to produce a precipitate of calcium sulphate. Explain why the number of drops of calcium chloride differs in the two experiments. I need equations, observations…
SERIAL DILUTION Show complete solution.
Volumetric pipettes are designed to deliver a precise amount of liquid, but only if you a. submerge the end of the pipette into a solution you are delivering. b. allow the pipette to drain freely, and leave any residual solution in the pipette. c. hold the pipette at a 45 degree angle and ensure that all the liquid is delivered.
Identify the characteristics of a good recrystallization solvent. Select one or more: Dissolves a chemical sample well at high temperatures. Is not an organic liquid with a low boiling point. Does not dissolve a chemical sample well at high temperatures. Does not dissolve a chemical sample well at low temperatures. Dissolves a chemical sample well at low temperatures.
The density of the first fraction collected would be expected to be close to a value of ______. 1.00 g./mL 0.895 g/mL 0.789 mL 0.950 g.mL
diffrentiate between oil in water emulsion and water in oil emulsion.
Write TRUE if the BOLD word/phrase makes the statement correct. Otherwise, write the correct WORD/PHRASE that will make the statement true. If there are two bold words/phrases in a number, write your answer for EACH of the bold words/phrases. 1. In the extraction of caffeine, NaOH was added to dry the collected organic layer. 2. Purification of caffeine via sublimation was possible because it has a high sublimation point at a temperature above its melting point. 3. The E/Z designation is used to describe the orientation of identical groups in alkenes.