Internal standard. A solution containing 3.47 mM X (analyte) and 1.72 mM S (standard) gave peak areas of 3 473 and 10 222, respectively, in a chromatographic analysis. Then 1.00 mL of 8.47 mM S was added to 5.00 mL of unknown X, and the mixed solution was diluted to 10.0 mL. This solution gave peak areas of 5 428 and 4 431 for X and S, respectively. (a) Find the response factor for X relative to S in Equation 5-9. (b) Find [S] (mM) in the 10.0 mL of mixed solution. (c) Find [X] (mM) in the 10.0 mL of mixed solution.(d) Find [X] in the original unknown.

Internal standard. A solution containing 3.47 mM X (analyte) and 1.72 mM S (standard) gave peak areas of 3 473 and 10 222, respectively, in a chromatographic analysis. Then 1.00 mL of 8.47 mM S was added to 5.00 mL of unknown X, and the mixed solution was diluted to 10.0 mL. This solution gave peak areas of 5 428 and 4 431 for X and S, respectively. (a) Find the response factor for X relative to S in Equation 5-9. (b) Find [S] (mM) in the 10.0 mL of mixed solution. (c) Find [X] (mM) in the 10.0 mL of mixed solution.(d) Find [X] in the original unknown.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter8: Sampling, Standardization, And Calibration

Section: Chapter Questions

Problem 8.16QAP

See similar textbooks

Similar questions

3c. A solution containing 2.50 mM X (analyte) and 1.20 mM S (standard) gave peak areas of 2509 and 7132 respectively, in a chromatographic analysis. Then, 1.00 mL of 6.00 mM S was added to 5.00 mL of unknown X and the mixture was diluted to 10.0 mL. This solution gave peak areas of 4016 and 3138 for X and S, respectively. Calculate i. the response factor for the analyte ii. the concentration of S (mM) in the 10.0 mL of mixed solutioniii. the concentration of X (mM) in the 10.0 mL of mixed solutioniv. the concentration of X in the original unknown solution
Internal standard. A mixture containing 12.8 mM analyte (X) and 44.4 mM standard (S) gave chromatographic peak areas of 306 for X and 511 for S. A second solution containing an unknown quantity of X plus 55.5 mM S had peak areas of 251 for X and 563 for S. Find [X] in the second solution.
Internal standard (As , Cs ), analyte with known concentration (Ax , Cx ) In a chromatographic equipment, a solution containing 0.006727 X and 0.008331 M S give peak area of Ax= 2316 and As= 207. To analyze an unknown sample, 5.0mL of 0.008331M S was added to 5.0mL of X, and the mixture was diluted to 50.0mL. This mixture gave a chromatography spectrum with area Ax= 3206 and As= 200. Find Cx.
A solution containing 2.30 mM of X (analyte) and 1.15 mM of S (standard) gave peak areas of 1728 and 6482, respectively, in a chromatographic analysis. Then, O.620 mL of 3.82 mM S was added to 2.75 mL of unknown X and the mixture was diluted to 10.0 mL. This solution gave peak areas 2501 and 2281 for X and S, respectively. Find the concentration of X in the original unknown.
A solution with 0.083 7 M X and 0.050 0 M S9 gave areas AX = 423 and AS9 = 372. Then 10.0 mL of 0.05 0 M S9 plus 10.0 mL of unknown were diluted to 25.0 mL. The chromatogram gave AX = 553 and AS9 = 286. Find [X] in the unknown.
Spectrophotometric Determination of a Metal A 100.00 mL of exactly 250.0 mg/L Cu2+ stock solution was prepared using a 99.95% pure Cu(NO3)2-3H20 (241.60 g/mol). From this stock, a series of standard solutions were prepared by pipetting certain volumes into 100-mL volumetric flasks, followed by adding 2.00 mL of concentrated NH3, and finally diluting to mark with deionized water. Additionally, a blank solution was prepared by using only NH3 and distilled water. Question: Why was NH3 added to each standard solution before diluting with distilled water? What will be the resulting color of the solution and why is this the color that is observed?
In a chromatography experiment, a solution containing 0.083 7 M X and 0.066 6 M S gave peak areas of AX = 423 and AS 5 347. (Areas are measured in arbitrary units by the instrument.) To analyze the unknown, 10.0 mL of 0.146 M S were added to 10.0 mL of unknown, and the mixture was diluted to 25.0 mL in a volumetric flask. This mixture gave the chromatogram in Figure 5-8, with peak areas AX = 553 and AS = 582. Find the concentration of X in the unknown.
From a 10-mL sample, a 1-mL aliquot was taken and diluted to 100mL. From this, a 5-mL aliquot was taken and diluted to 20mL.The final 20mL was found to have a concentration of 0.004M analyte X.What is the concentration of analyte X in the 10-mL sample?
Q1: The following are relative peak areas for chromatograms of standard solutions of methyl vinyl ketone (MVK) MVK concentration mmol/L 0.5 Relative peak area 3.76 1.5 9.16 2.5 15.03 3.5 20.42 4.5 25.33 5.5 31.97 A sample containing MVK yielded relative peak area of 21.3. Calculate the concentration of MVK in the sample.(use excel)
A spectrophotometric method for the quantitative determination of the concentration ofPb2+ in blood yields an Ssamp of 0.133 for a 1 mL sample of blood that has been diluted to 6 mL. A second sample is spiked with 1 µL of a 1467 ppb Pb2+ standard and diluted to 6 mL, yielding an Sspike of 0.491. Determine the concentration of Pb2+ in the original sample of blood.
A second spectrophotometric method for the quantitative analysis of Pb2+ in blood yields an Ssamp of 0.712 for a 5.00 mL sample of blood. After spiking the blood sample with 5.00 μL of a 1560 ppb Pb2+ external standard, an Sspike of 1.546 is measured. What is the concentration of Pb2+ in the original sample of blood?
The ethyl acetate (CH3COOC2H5) concentration in an alcoholic solution was determined by diluting a 10.00-mL sample to 100.00 mL. A 20.00-mL aliquot of the diluted solution was refluxed with 40.00 mL of 0.04672 M KOH: ethyl acetate.JPG After cooling, the excess KOH was back-titrated with 3.85 mL of 0.04644 M H2SO4. Calculate the %(w/v) CH3COOC2H5 in the alcoholic solution. MM CH3COOC2H5: 88.11 MM NaOH: 40.00 MM H2SO4: 98.08