In the RC circuit below, Vs=12, R =43k2, and the capacitor =71 µF. if, initially, the switch is at position A and the capacitor is fully charged, what time, in seconds (to two decimal places), will it take V to reach 3 Volts after the switch is moved from position A to position B? R Vs A B V₂

In the RC circuit below, Vs=12, R =43k2, and the capacitor =71 µF. if, initially, the switch is at position A and the capacitor is fully charged, what time, in seconds (to two decimal places), will it take V to reach 3 Volts after the switch is moved from position A to position B? R Vs A B V₂

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Related questions

Q: For the network, determine: a. IB. b. lc. c. VCE. d. Vc.

Q: 3. From the circuit shown below, what should be the value of R1 for the circuit to have a gain of…

A: As per our company guidelines we are supposed to answer only first question kindly repost the other…

Q: 2. A copper rod is 3 m long and 4 mm diameter. Compute its resistance if the resistivity of the…

A: It is given that: Length=L=3 mDiameter=d=4 mm=4×10-3 mResistivity=ρ=1.76×108 Ω-m

Q: Control system If an electrical network has three energy-storage elements, is it possible to have a…

A: Control system is the set of the mechanical and electrical device to regulate and it provide the…

Q: Show how using p-n-p transistor connected in common-emitter configuration it can be used as an…

A: The Common-Emitter transistor configuration is used as a amplifier in applications like Audio…

Q: Find inverse Laplase transform of (s)=2as/ (S+1) (s²+4) where a=

A: It is given that: Xs=2ass+1s2+4a=8so,Xs=16ss+1s2+4

Q: A student is performing on 230 v dc shunt motor in which he uses an armature resistance of 0.22 ohm…

A: A motor is an electromechanical device which is used to convert the electrical power into mechanical…

Q: E A- Name the advantages of optical fiber over twisted-pair and coaxial ?cable

A: The advantages of optical fiber over twisted-pair and coaxial cable are listed below

Q: Determine the current supplied by each voltage source (8 V,12 V). using superposition theorem in…

A: This question comes under electrical circuit theory . It is related to super position theorem . In…

Q: Q1) The signal x(t)= 5 cos (40nt) is to be sampled for digital transmission with bit rate 400bps…

A: Given data : Signal Xt=5cos40πt Bit rate Rb=400bps

Q: Q3.2: For the circuit shown below, in order to find the value of i 3A loov + 1052 ww io ← www 65 55…

A: Network Analysis : Node voltage Method uses Kirchhoff's current law which states that the algebraic…

Q: The switch in the following circuit has been opened for a long time. It is closed at t = 0.…

A: In this question, We need to determine the voltage across the resistance 2 ohm We know, voltage…

Q: The three conductors a,b,c of a 3 phase are arranged in a horizontal plane with Dab=2m, Dbc=2.5m.…

Q: Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer.…

A: Transformer is the static device it work on the principle of faraday law of mutual inductance. It…

Q: Problem 6 An electrical circuit consist of a series connected resistor (100 ohms) and a coil with…

A: Capacitive reactance inversely proportional to frequency Inductive reactance directly proportional…

Q: 10.16. Determine the causality and the stability for the systems with the following impulse…

Q: A 6-ohm resistor is connected in parallel with a 300 uF capacitor and the circuit is supplied by a…

Q: Using the SR flip-flop, implement the 4-bit circuit that performs the DEC (Decrement) operation. (So…

A: We need to design a 4-bit circuit that performs the decrement operation. So, when the decrement…

Q: answer with solution C(s) Find the transfer function R(s) d²C d 2#*C(Đ) +2&°C(Đ) dt² ¹+2+C(t)=r(t)…

A: Given here a differential equation and asked to find the transfer function.we know that L c t = C…

Q: Problem 7: Consider the following circuit of three resistors (R₁, R2, and R₂), with batteries that…

A: (a) The circuit is shown below: Applying K.V.L in the top loop,…

Q: Consider the following signal f(t)=sin(2nt)+3sin(8πt)+cos(3nt). (a) What is the highest angular…

A: As per the guidelines of bartleyby I need to answer first three subparts only so kindly repost other…

Q: H.W3: Consider the circuit a. Find RT 9V b. Calculate the current across each resister. c. Determine…

A: This question belongs to circuit theory . It is based on the concept of current division law and…

Q: 4. If a 60-Hz three-phase motor has a nameplate full-load speed of 500 rpm, the number of pole-phase…

A: Given a three-phase motor with, Frequency, f = 60 Hz Full load speed, Ns=500 rpm

Q: 2.) Find the values of VG. Ig. VD, & Vc for the circuit when B=100, Ipss = 5mA and V₂ =- 4V. 24V R2…

A: The given circuit is

Q: Q1: Simplify the block diagram shown in Fig. (1), then obtain the closed-loop transfer functions…

Q: Vi Determine the voltage gain. SHOW YOUR SOLUTIONS R1 ww R5 ww 10kQ 10kQ R2 >10kQ R3 >10KQ R4 10kQ…

A: Voltage gain:

Q: For 3G cellular data networks, what function does the RNC (Radio Network Controller) play?

A: RNC represents Radio Network Controller. The function RNC plays in this architecture is to control…

Q: Two 11000/400 V, transformers are operated in parallel to share a load of 250 kVA at 0.85 power…

A: Given :KVA rating of Transformer 1 = 100 KVAKVA rating of Transformer 2 = 200 KVAR1=0.009…

Q: Determine the I.D.F.T

Q: A capacitive MEMS accelerometer uses which one of these scientific principles or quantities?

A: The answer is inertia. Why it is discussed below.

Q: Beside is a pnp transistor circuit with CE (common-emitter) configuration. Let VBE(On) = 0.6v, B =…

Q: as/ Find the value of R, for maximum power transfer in the circuit of Fig. Find the maximum power.…

A: This question belongs to circuit theory . It is based on the concept of maximum power transfer…

Q: 5.6 ΚΩ IR www 8 mA +₁₁ 2.2 ΚΩ 16 V Fig-2- Find (IR) through resistor R = 2 k ohm.using Norton's…

Q: Determine the current supplied by each voltage source (8 V,12 V). using superposition theorem in…

A: This problem comes under electrical network theory. It is about superposition theorem . Problem…

Q: If the Young's modulus 'E is equal to the bulk modulus 'K', then what is the value of the Poisson's…

A: Young Modulus and Bulk Modulus are the property of material which is very important to know the…

Q: Determine the value current supply (IT) in figure (1). Fig.1 lon Голі 55 u Гол Slov IT 24V VT

A: This question belongs to circuit theory . It is based on the concept of calculation of current in…

Q: Q.3: A 18kVA, 200/600V, 50-Hz, single-phase transformer, the open and short circuit tests data are…

A: Q3. Given data is shown below. O.C test : 200V, 3.5A, 600W S.C test : 15V,30A,400W 1φ transformer,…

Q: Two 11000/400 V, transformers are operated in parallel to share a load of 250 kVA at 0.85 power…

A: It is given that: A:100 KVA; 0.9 % resistance and 10 % reactanceB:200 KVA; 1 % resistance and 5 %…

Q: or the function F(s) 1+5/60 a) The poles of the function are.

A: Given data, The transfer function Fs=s1+s60

Q: Determine the current supplied by each voltage source (8 V,12 V). using superposition theorem in…

A: In this question, We need to determine the current in the each voltage source. Here 2 voltage…

Q: Vi R1 ww 10kQ [R2 >10KQ R5 mw 10k [R3 -10k R4 >10KQ R6 ww 10k Vo

A: Voltage gain:

Q: 8. What is the primary difference between the BJT and the FET? a. current-controlled device and…

A: From the given options we need to determine the primary difference between the BJT and FET. BJT: BJT…

Q: Vi Determine the voltage gain. SHOW YOUR SOLUTIONS R1 ww R5 ww 10kQ 10kQ R2 >10kQ R3 >10KQ R4 10kQ…

A: Operational Amplifier:

Q: Find the Current Io. In figure (2). Чта (1) 2mA Ika mm Ika Iy 2 KA In lkn Is Is 6V Elkn 16mA.

Q: Q1/A- For the circuit shown in Fig., find: (a) V₁ and V₂ (b) the power dissipated in the 3K0 and 20…

A: 1) (A) To find (a) voltage v1 and v2 b) power dissipation in 3 Kohm and 20 Kohm resistor c) power…

Q: A 10-hp, 4 pole, 25Hz, 3-phase induction motor is taking 9100 watts from the line. Core loss is 290…

A: Given data, Frequency f=25Hz No. of poles P=4 Input power Pi=9100W Core loss Pc=290W Stator copper…

Q: A three-phase star-connected, 50-Hz generator has 48 coils per phase and a flux per pole of 0.1 Wb.…

A: Note: Since nothing is specified, so we will consider full pitch coil with pitch factor kc=1. One…

Q: c) Core diameter increases. The coupling efficiency between the optical Radiation pattern of the…

A: 1. Choice A As the refractive index of the cladding decreases, the field view of step index fibre…

Q: Vs Rsig CG V₁ G RG O Draw the equivalent circuit. DD Ro S Rs Cs RL Vo

Q: C- True and False (correct the false) 1- Class-A: the output stage conducts for a full 360° (a full…

A: 1) True because In Class A power amplifier the output collector current flows for complete 360° of…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

In the RC circuit below, Vs=12, R =43k, and the capacitor =71 µF. if, initially, the switch is at position A and the
capacitor is fully charged, what time, in seconds (to two decimal places), will it take Vx to reach 3 Volts after the
switch is moved from position A to position B?
R
Vs
A
B
V.
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the unit of measurement for the strength of a capacitor? microamp microtorque microfarad microwatt
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
List the five capacitor replacement rules.
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
A 4.7 Micro-Farad capacitor is in series with a 470 K-Ohm resistor with a 12V power supply. How long will it take for the capacitor to fully charge? OA 4.7 sec O B. Cannot be determined O.11 sec O D.470 ms O E. very quickly, it cannot be seen
1)The value of the capacitance reactive power in VAR is? /2) The value of the capacitor in micro farad is?
Make a clamper circuit using 500 µF capacitor, silicon diode, and a 100 KΩ resistor connected to a 10 Vpeak sine wave. Draw the output waveform and indicate the amplitude and the time values supported by your solutions. Do these for both positive and negative clamper circuit. Show your circuits first before your solutions and waveforms.
Three capacitors 6, 10 and 15 uF are connected in series across a 100 volt supply. Find the voltageacross the 10uF capacitor.
In the diagram below, the switch S has been closed for a long time. A) What is the output voltage Vout? What is the charge on the capacitor? b) The switch is opened, so the output voltage increases. What is the time constant that describes the charging of the capacitor in terms of R and C? c) When Vout reaches 10 V, the switch closes and the capacitor begins to discharge. What is the time constant that describes the discharging in terms of R and C? Hint: Apply Kirchhoff's Rules to both loops and the sum of the currents at the junction above the capacitor in the diagram, and use I=dq/dt. If the switch opens when Vout reaches a lower value, say 5V, the capacitor will charge again, and thus one can cycle the voltage with a time constant determined by the circuit: this demonstrates the principle of operation of an electronic timer. 4R S 15 V Vout R