In junction diode forward biased the thickness of the depletion region is *
Q: Find V, in the circuit shown in the figure below using Thevenin's theorem.
A: The thevenin's equivalent circuit can be calculated by using the nodal analysis.
Q: In the AC circuit shown in the figure below, R = 70.0 2 and the output voltage of the AC source is…
A: Given, An Ac circuit shown below, R=70.0 Ωv=∆Vmaxsinωt∆vR=0.270Vmax at t=0.0080 s
Q: Two generators operating in parallel supply a total load current of 150 A.The terminal potential…
A: The circuit diagram of the above parallel combination will be like:
Q: 13. We wish to design the CE stage of Figure for a voltage gain of 20. What is the minimum allowable…
A: Given circuit, To design CE stage, Voltage gain, AV=20 Q1 must remain in active mode VA=∞VBE=0.8 V
Q: 2. A 15-km, 60Hz, single phase transmission line consists of two solid conductors, each having a…
A:
Q: What the range of values of Vi that will maintain the Zener diode in the "on" state. R "L + 220 Ω P…
A:
Q: cavity b. Cathode c. Catcher cavity d. Collector 30. At what position is the input signal inserted…
A: These are the few questions related to the working and designing of klystron amplifier.
Q: v= Ξ V = 10 V Ο 185 mA 46 mA Ο Ο 50 Ω R₁ 5ΩΣ R A B D
A:
Q: A 50-horsepower, 460V, 60Hz, 3-phase induction motor has a Nameplate Rating of 60 amperes. The…
A: Given information, Rated output power is P=50 HP. The rated voltage is VL=460 Volts. Nameplate…
Q: 42 cm 16 m 16 m Determine the inductance per meter and the inductive reactance if the size of the…
A:
Q: How many turns are needed in a transformer to step from 18 V to 24 V, if the secondary coil has 250…
A:
Q: Discuss the concept of an Electrical fault. How can we prevent such catastrophic incident for such…
A: Electrical Fault in an electrical equipment or apparatus is a kind of imperfection in electrical…
Q: Given: Vcc = 6V RB =10k RC=1k B(beta)=100 hie=1k. Identify: a. What is the voltage gain of the…
A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…
Q: 32. A high power microwave pulse of the order of megawatts can be generated by: a. Magnetron b.…
A: 32) A High power microwave Pulse can be generated by Magnetron. hence, option "a" is correct. a)…
Q: 9.(a) A three-phase, half-wave rectifier feeding a resistive load is supplied by a star/star type of…
A: In this question we need to find a firing angle of the given three phase half wave rectifier . For…
Q: 4- If the base current in npn transistor = 2 mA, and (a) - 0.97, so, the collector current= @ 64.67…
A: Given data, In an npn transistor Base current, IB=2 mA αe=0.97
Q: A2. (a) Simplify the following logic functions using Boolean Algebra. (i) F=Y+XZ + XYZ (ii)…
A: Given logic functions, (i) F=Y+XZ+XYZ(ii)F=YX+YY+Z
Q: for the circuit shown in fig find the current I? 5/2 f = 50 M₂
A:
Q: A coil of resistance 10 22 and inductance 0.8 H is connected to 200 V dc supply. The initial rate of…
A: Given: A coil of resistance, R=10 Ω Inductance, L = 0.8 H DC supplied voltage, V = 200 V
Q: j10 Q Find Z₁1- 502 www j15 Q 2 N 2¹
A: Given two port network,
Q: in RLC drcuit we have: y() is output and x(t) input, R= 1 Ohm, C= 1 Farad, L=1 fenry, , a.find H…
A:
Q: A 1 mA meter movement with internal resistance of 100 ohm, is to be converted into a 0 -100 mA…
A: given 1 mA meter movement with internal resistance of 100 ohms , is to be converted into a 0-100 mA…
Q: 4. Sketch the output V for the given network below. 0 1 k +8 V -8 V ō Si
A:
Q: For the circuit shown in Figure 2 let Vcc=5 V, R₂ = 4 kQ2, Re = 3 k2, R₁ = 60 k2, and R₂ = 40 k2.…
A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…
Q: Kp=2, Ka-3, Km=1, J=1, F=5, a=1 and h=1. &(s) E(s) V(s) Kp OR(S) Ka Km Ⓒm(s) s(Js + F) a -e, (s) +…
A:
Q: A 50-horsepower, 460V, 60Hz, 3-phase induction motor has a Nameplate Rating of 60 amperes. The…
A: Given information about a 3-phase induction motor is, Rated output power P=50 HP. The rated voltage…
Q: 1.8 A motor drive is supplied from a three-phase power converter has conversion efficiency of 90 %…
A:
Q: Consider the circuit shown in Figure 2. The transistor parameters are ß= 100 and VA = 100 V.…
A:
Q: Direct transmission of message signal without modulation can be cause. Problems Noise Fading…
A: These are the few questions related to the understanding of basic modulation techniques and their…
Q: a + 10 V M 50 Ω b C e 25 Ω 75Ω 100 Ω 25 Ω W 50 Ω d
A: According to ohms law, Current,I = voltage,V/resistance,R
Q: The transfer function of a plant is: Gp(s) = s+a where a and b are arbitrary constants and a,b > 0.…
A:
Q: The potential difference across a 5 kΩ is 12 V. Find the current flowing through the resistor:…
A: given the potential difference across a 5 kΩ is 12 V. we have to find the current flowing through…
Q: A 0.5 Q resistance is required to be connected in parallel to a moving coil instrument whose full…
A: In this question we will find internal resistance of instrument....
Q: What minimum value of series resistance is required when three 10-watt, 10-volt, 1000-mA zener…
A:
Q: A spring has a spring constant of 560 N/m. The potential energy stored in the spring when stretched…
A: Given data, Spring constant, k=560 N/m Stretched length, x=15 cm
Q: (s)=s4+2s3+3s2+20s+5. Find: Number of poles in the left-half plane? Number of poles in the…
A:
Q: 4.41) If the Q- factor of a coil at resonant frequency of 1.5 MHz is 150 for a series resonant…
A: Given: Q factor, Q = 150 Resonant frequency, fo=1.5 MHz
Q: (Q14) An RC phase shift oscillator using Op-Amp is shown. Given the value the electric resistance…
A:
Q: The load is given as 6+8j ohms in the system. If the apparent power of the load is 15 kVA, the…
A: Given, Load impedance, ZL=6+8j ohms Apparent power, S = 15 kVA
Q: 35. If the peak amplitude of a low-pass filter output is 5V, what voltage will correspond to the…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: Determine the Q point of the transistor circuit shown in Figure. Given B = 200 and VBE = 0.7V.
A:
Q: A common-source amplifier is shown in Figure Q.2(c). Given that Z₁ = 20 kn, Rsig = 1 ks2, gm = 3 mS,…
A: The common-source amplifier circuit is shown below, Where,Zi=20 kΩRsig=1 kΩgm=3 mSRo=2 kΩCgd=10…
Q: B Figure 1 (for numbers 6 to 9). VB is 3V, Vcc is 9V, RB is 10K and RL is 1K and (beta)=100. IE R₂…
A: Given data Vb=3v Vcc=9v Rb=10k Rl=1k Beta=100
Q: 1 Three infinite current sheet K₁ -10 az at x = 2 Find -60 äz at x = 7 and K 2 = 20 az at x = 5 and…
A: We need to find out the magnetic field for given current distribution .
Q: What minimum value of series resistance is required when three 10-watt, 10-volt, 1000-mA zener…
A: From the Question What minimum value of series resistance is required when three 10-watt, 10-volt,…
Q: For the same secondary voltage, the output voltage from a center-tap rectifier is. than that of…
A:
Q: A uniform line charge of 2 µC/m is located
A:
Q: 6. To make the transistor operating as an amplifier, junction one should be biased, whereas the…
A: 6. Answer: forward, reverse Explanation: a. It is a valid option. If one junction is forward…
Q: Determine the average emf induced in a coil of 200 turns wound on a magnetic circuit having…
A:
Q: 11 R, L1, L2, mH mH 2k 10 50 1. graph showing how the amplitude of signal changes when the frequency…
A:
Step by step
Solved in 2 steps with 2 images
- Lamount of current will flow through the p-n junction germanium diode for a forward bias of 0.15 V with reverse saturation current equal to 1.5 mA and voltage equivalent temperature value of 20.25 mV.determine the current flowing through the zener diode having breakdown voltage of 5.6v of the circuit shown belowDetermine vo and the required PIV rating of each diode for the configuration in the following figure.
- Draw a circuit containing forward bias diode and then draw the graph I/N characteristic in silicon semiconductorDraw the corresponding output waveform of the double diode partial limiter below using simplified diode model. Indicate all the necessary voltage levels and use Silicon diodes. 20 VP-P 1KQ M D1 9V D2 4.5V VOUTFor the parallel diode configuration of the figure, determine Vo, l. Ipi and Ipz- 10 V
- The 4-layer diode in below figure is biased such that it is in the forward-conduction region. Determine the anode current for and VBRF) = 20 V, VBE = 0.7 V, VCE(sat) = 0.2 V. Rs 1.0 kn VBIAS 25 VIn reference to the output waveform below and using ideal diode model: Vout +7.5V -3.5V a. Analyze the behavior of the circuit and fill up the table below. Vin Diode state Vout (FB or RB) +6V OV -3V -6V b. Draw the clipper circuit that will produce the given output waveform.Draw the characterstic r-l for silicon diode in the forward bais and explain it.
- Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode. 4k02 2V 1k02. Off, 0.00mA, 0.4V O Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v Option 5u= 6sinot V. V. For the circuit of Figure, we have known E=3V, Use the ideal diode model to analyze the circuit and draw the waveform of the output voltage. 6V cot Uj EIdeally the voltage drop across a diode under off state must be O a. higher than the forward biased voltage O b. 00 O c. 0 O d. equal to the forward biased voltage