v= Ξ V = 10 V Ο 185 mA 46 mA Ο Ο 50 Ω R₁ 5ΩΣ R A B D
Q: 76612 (a) Design an Aryton (universal) shunt circuit to convert a basic PMMC meter with an internal…
A:
Q: List the various mechanical and electrical additions (minimum of 8) needed for an existing…
A: When we want to connect any DG set to industrial plant or any load , there are many electrical and…
Q: npn -24 - عند استخدام تـرانـزسـتـور npn transistor was used as a current كمكبـر لـلـتـيـار فـإذا…
A: Given, A NPN transistor is being used as a current amplifier. Base current, IB=1 mA Current gain,…
Q: What are the factors to be considered in the Preparation and Design of Electrical System involved in…
A: Electrical system is considered for any circuit or any setup having electrical devices and many…
Q: The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to…
A: Given, Power consumed by a coil when connected to 30 V DC supply, Pdc=300 W Power consumed by a coil…
Q: What is the induced voltage Vs in the transformer, if the primary voltage Vp-220 V with number of…
A: Given, Primary voltage, Vp=220 V Number of primary turns, Np=50 Number of secondary turns, Ns=10
Q: Draw the output voltage waveform for the circuit in (b), and (c). and include the voltage values. R₁…
A:
Q: Answer the following with illustration and solution. 1.) A circuit consisting of a resistor of…
A: The required parameter can be obtained by calculating the impedance of the capacitor and then by…
Q: Compute the values of L and C to give a bandpass filter with a center frequency of 2 kHz and a…
A:
Q: Explain the working of 3 stage RC phase shift Oscillator. Design a 5 stage RC phase shift oscillator…
A: Oscillator Oscillator is a electronic or mechanical device, its based on working of oscillation. we…
Q: 1. The position of a point in cylindrical coordinates is specified by (4,27/3,3). What is the…
A:
Q: Find i₁0 for the given circuit below: www 2Ω 4Ω 12 V + 32 V ίγο 10 Ω
A: Given circuit,
Q: For a negative unity feedback system, using Routh-Hurwitz criterion for stability, determine the…
A: given transfer function.
Q: An impedance coil has a resistance of 20Ω and an inductive reactance of 40Ω. For what value of…
A:
Q: Determine the average emf induced in a coil of 200 turns wound on a magnetic circuit having…
A:
Q: A copper wire 2 m long, with a diameter of 3 mm, has a resistance of 0.0012 2 at 20 °C. What will…
A: Given, A copper wire has Length, L=2 m Diameter, d=3 mm Resistance Rref=0.0012 Ω at Tref=20°C…
Q: 1. The position of a point in cylindrical coordinates is specified by (4,2π/3,3). What is the…
A: given the position of the point in cylindrical coordinates is specified by 4 , 2π3 , 3 generally in…
Q: ILS gives lateral and vertical guidance towards the runway To use ILS aircraft must contain the…
A: ILS stands for instrument Landing system these are for aircrafts while landing it helps to provide…
Q: 2. For an ideal amplifier, the input impedance should be output impedance should be OOohm and…
A:
Q: The load is given as 6+8j ohms in the system. If the apparent power of the load is 15 kVA, the…
A: Given, Load impedance, ZL=6+8j ohms Apparent power, S = 15 kVA
Q: A four-pole, lap-would DC machine has 462 conductors in the armature. The average flux per pole is…
A:
Q: EXPERIMENT #4: BJT VERIFICATION MEMBERS: OBJECTIVES: Verify the integrity of the junctions of a ppp…
A: BJT- It is one of the type of transistor. Bipolar Junction Transistor is known as a bipolar because…
Q: Due to mutual inductance between two coils, there is an induced emf in one coil due to a change in…
A: Answer:True
Q: The maximum power dissipation of a transistor is 100mW. If VCE = 20V, what is the maximum collector…
A: Given, PD = 100 mW = 0.1 Watt VCE = 20 V
Q: What is the equivalent transfer function of the following block diagram? G₁ Input (R) Output (C) G₂
A: The question is solved by block diagram algebra by assuming dummy variables and then writing…
Q: What is the induced voltage Vs in the transformer, if the primary voltage Vp-220 V with number of…
A: Given data, Primary voltage Vp=220 V Number of turns in primary Np=50 Number of turns in secondary…
Q: Gp(s) R(s) S c(s) (s + 2)(s² - 25) Figure Q2a The transfer function of an inverted pendulum plant is…
A: Transfer function- Transfer function basically is the mathematical representation of the systems…
Q: 2. Sketch the output V and determine the DC level of the output signal for the given network below.…
A:
Q: The initial and final values of f(t)=15-10t-10e e-20r are respectively (a) 5 and ∞ (b) 5 and -co (c)…
A: Given function, ft=15-10t-10e-20t
Q: Three infinite current sheet K₁ K3 = -10 az at x = 2 Find - 20 az at x = 5 and = -60 äz at x = 7 and…
A: We need to find out the magnetic field for given current distribution
Q: For a series R-L circuit i(t)=√√2 sin (cot-45°) If @L=1 Q, the value of R is (a) 1 Ω (b) 3 Ω (c) 13…
A: Phase angle in series RL circuit calculated tanϕ= WL/R From the given current expression, we can…
Q: 4.41) If the Q- factor of a coil at resonant frequency of 1.5 MHz is 150 for a series resonant…
A:
Q: A 50-horsepower, 460V, 60Hz, 3-phase induction motor has a Nameplate Rating of 60 amperes. The…
A: Given information about a 3-phase induction motor is, Nameplate rating of current is 60 amperes.…
Q: On a high-end gaming computer, the component that uses the most power is the... What is the maximum…
A: On a high-end gaming computer, video is required because gaming computers require high-quality…
Q: 12. When we add a resistor on the emitter port of the transistor in the amplifier design, the…
A: The main purpose of the emitter resistor to keep circuit stable. More the value of resistance ,more…
Q: The position of a point in cylindrical coordinates is specified by (4,2π/3,3). What is the location…
A:
Q: Determine Zi, Zo, and Vo for the network of Figure below if Vi = 4 mV, Vaso = -0.95 V
A: The required parameters can be calculated by using the AC analysis of FET amplifier.
Q: Determine the signal level sensed by the amplifier if the circuit has an input impedance of 1 kohm…
A:
Q: A 10 cm length of a K-band (a = 1.06 cm and b = 0.43 cm) copper (o= 5.8x107) waveguide is filled…
A: A 10 cm length of a K-band (a=1.06 cm and b=0.43 cm copper σ=5.8×107 waveguide is filled with a…
Q: Find the total capacitance in micro farads of the combination of capacitors shown in the figure…
A:
Q: solve using thevenins theorem (draw the step by step changes in the circuit diagram) solve the…
A: Given
Q: Q1. A 10 cm length of a K-band (a = 1.06 cm and b = 0.43 cm) copper (o= 5.8x107) waveguide is filled…
A: A 10 cm length of a K-band (a=1.06 cm and b=0.43 cm copper σ=5.8×107 waveguide is filled with a…
Q: Jse superposition to solve for in (t) 20 με 50 cos 2000r V 40 mH 2 sir 4000r A 80 Ω 60 Ω 100 Ω 24 V
A:
Q: Determine the average emf induced in a coil of 200 turns wound on a magnetic circuit having…
A: Given a coil with, Number of turns, N = 200 Reluctance, S = 2000 AT/Wb Change in time, t = 10 ms…
Q: 4. What is problem with this circuit? * Vcc J Rc 1kQ Ка Vin No DC biasing on the collector The…
A:
Q: (a) State two (2) differences between BJT and FET. (b) Figure Q.1(a) shows a MOSFET amplifier…
A: The required parameters can be calculated by using DC analysis of the MOSFET amplifier.
Q: For a negative unity feedback system, using Routh-Hurwitz criterion for stability, determine the…
A:
Q: Combination of Resistors deals with the equal current in series connection and equal current in…
A:
Q: 3.80 In the circuit as shown in figure, the switch is closed at t= 0. The current through the…
A:
Q: H4. Find the number of left, right and jw-axis poles in these following characteristic equations: I.…
A: Based on Routh-hurwitz table we can say the number of poles on right side ,left side, jw axis of a…
Step by step
Solved in 2 steps with 2 images
- Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load d. a signal lightThe current through the diode in the circuit given in the Figure below when Vy = 0.7 V is? ww 8092 12V Select one a. 24.26 mA b. 13.09 mA c. 58.23 mA d. 40.13 mA 40-52 ww 3092 IDPROBLEM: The diode (blue line) should be at -10V not -8V SOFTWARE USED: LTspice XVII---Figure 1 is my work, and figure 2 is the correct sample. Please tell me what I did wrong. Thank you :))---Below is the .asc filehttps://www.mediafire.com/file/zxauoh86zi79nfu/EXPERIMENT_01.asc/file
- > * Determine the voltage across the diode in Figure below, assuming an ideal diode 5 V O 4V O-3V O 7V O 8V www 10 +1₁ 8 VFind the current through the diode in the circuit shown in Figure. Assume the diode to be ideal. 50 Ω A R1 V = 10 V 503R D B (i) 0,5A O 0.27A O 0,2A 0.38A O 100 wwwwthe input voltage V1 is a sinusoidal voltage with maximum value of 4V. If the threshold voltage of the diodes is 0.1 V, plot Vo versus VI. +10 V 10 k2 o vo 10 k2 10 k2 -10 V wwwo
- A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1Determine the voltage across the diode in the figure , assuming an ideal diode. 10 Ω 10 V= 8 V Select one: a. 0.7 V b. 2 V c. O V d. -2 VExercises: Determine VO and Ifor each circuit in figures. Assume that each of the diode in these circuits has a forward voltage drop of 0.7 V. V₁. D 1.1.2 D V. $5.140 1.V₁=V₁=OV. 2.V₁ =V₁=SV, and 3.V=OV & V, -5V. (d) C C ΣΙΩ T-15V D₂ +201 20 V₂ 14.02 I-15V 1. No pulses at either A or B. 2.A 30 V positive pulse at A or B, and 3. Positive pulses (30 V) at both A and B. (e)
- Find the current through the diode in the circuit shown. Assume the diode to be ideal. A 50 92 www R₁ V = 10 V O 185 mA O 46 mA O 140 mA O 28 MA 502 R₂ B DThe D diode used in the diode circuit shown in the figure is a silicon diode. a. Plot the output voltage of the circuit. b. Describe the working principle for each phase in detail R1 10 kN V out +12 V D R2 100 N Vin-15 sin(wt) R3 220 NFor the circuit below with E = 10 V, R = 5800 N. Find the following: a) current in the circuit b) voltage across the diode c) voltage across the resistor Anode (A) Cathode (K) b E R wwww