In Figure (a), both batteries have emf ɛ = 1.70 V and the external resistance R is a variable resistor. Figure (b) gives the electric potentials V between the terminals of each battery as functions of R: Curve 1 corresponds to battery 1, and curve 2 corresponds to battery 2. The horizontal scale is set by Rg = 0.500 N. What is the internal resistance of (a) battery 1 and (b) battery 2? 0.85- R R, -0.510 R (2) (a) (b) (a) Number i Unit (b) Number i Unit A)A

In Figure (a), both batteries have emf ɛ = 1.70 V and the external resistance R is a variable resistor. Figure (b) gives the electric potentials V between the terminals of each battery as functions of R: Curve 1 corresponds to battery 1, and curve 2 corresponds to battery 2. The horizontal scale is set by Rg = 0.500 N. What is the internal resistance of (a) battery 1 and (b) battery 2? 0.85- R R, -0.510 R (2) (a) (b) (a) Number i Unit (b) Number i Unit A)A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 1PA: Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter...

See similar textbooks

Similar questions

How temperature effect conductivity? Explain with the help of following equation. m e'n7'
An ammeter has been designed by indirect method with current ranges 1A, and 5A, if PMMC meter have internal resistance of 50 (2 and half scale current of 0.5 mA. Ra and Rb will be --- ohm Ra= 0.05005 , Rb=0.01001 Ra = 0.04004 , Rb = 0.01001 Ra= 0.05005 Rb= 0.04004
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). Choices: 0.11A 22mA to 89mA 9A 0.11A to 9A Plss show complete solution
the non-inductive resistance of kelvin double bridge are set at 100ON each, the standard resistance is set at 0.10020 and the low resistance 0.0000122 was very low. determine the unknown resistance
Determine the loop currents Ia, I,, and Ic. 100 Ic 100 100 100 100 Ib 55V 100 V la
Q2) Consider the circuit in Figure (3), and answer 3 branch only. a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across each half of the secondary. d) Sketch the voltage waveform across RL. 4:1 120 V rms RL 1.0 k2 D2 eelee
The conductance of a 9230 resistance is a) 1.08 * 10-3 mho b) 1.08 * 10-4 mho c) 1.02 * 10-3 mho d) 1.02 * 104 mho
Two resistors RA and RB are connected in series across a 120-V source. When a 30,000-ohm voltmeter is connected across RA and then across RB, the instrument deflection is 48 volts in each case. What are the ohmic values of the resistors?
4. With reference to the Paschen curve below, Breakdown voltage (V) 60 55 50 45 40 35 30 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 pd (cm-torr) If a discharge at p = 0.1 torr, d = 20 cm is to be initiated, what is the voltage required to cause a breakdown? What will be the breakdown voltage if p = 0.025 torr, d= 20 cm?
calculate the Load current and Load voltage of the given figure
6. The main difference between resistance R and capacitive reactance X, is that (a) Xc is the same for both DC and AC signals, where R depends on frequency of the AC signal (b) R is the same for both DC and AC signals, where X depends on the frequency of an AC signal (c) R is measured in ohms and X is measured in farads (d) None of the above
Determine the DC currents (IB, Ic and lĘ) and dc junction voltages (VBE, VCE and VCB) Ig=Blank 1 mA, Ic=Blank 2 mA, IĘ=Blank 3 mA, VBE= Blank 4 V, VCE = Blank 5 V and VCB = Blank 6 V Use 2 decimal places. Use the following values: VBB = 2V RB = 7 kQ Rc = 248 Q Vcc = 19 V BDc = 56 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer Blank 4 Add your answer Blank 5 Add your answer Blank 6 Add your answer