In a given DC motor, the output power is 45 HP, and the copper losses are 2.005 KW. If the rotational losses is one tenth of the output power, find the converted power and the efficiency of the motor. Select one: O a. None O b. Pcony = 33.57 KW and % efficiency = 89.2 % O C. Peony = 39 KW and % efficiency = 75.8 % %3D O d. Peony = 36.927 KW and % efficiency = 86.2 % !3!

In a given DC motor, the output power is 45 HP, and the copper losses are 2.005 KW. If the rotational losses is one tenth of the output power, find the converted power and the efficiency of the motor. Select one: O a. None O b. Pcony = 33.57 KW and % efficiency = 89.2 % O C. Peony = 39 KW and % efficiency = 75.8 % %3D O d. Peony = 36.927 KW and % efficiency = 86.2 % !3!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a given DC motor, the output power is 20 HP, and the copper losses are 1.1 KW. If the motor is operating at 87 % efficiency, find the converted power and the rotational losses. Select one: a. Pconv = 16.05 KW and Prot = 1.13 KW b. Pconv = 17.15 KW and Prot = 3.11 KW c. Pconv = 14.92 KW and Prot = 1.35 KW d. None
1) A 100-V shunt motor is developing 6 hp while operating at an overall efficiency of 86%. The armature and shunt field resistances are 0.06 and 50 ohms respectively. Determine the stray power losses. 2) The field and armature resistance of a 400 V shunt motor are 200 ohms and 0.1 ohms, respectively. The motor takes 30 A of current while running at 1000 rpm. If the frictional losses are 400 W, determine the motor efficiency. 3) In a brake test of an elevator door, the ammeter and voltmeter measuring the input read 34 A at 220 V. The speed of the motor is found to be 910 rpm and the balance on the 0.61 m brake arm reads 11.9 kg. The dead weight of the arm is found to be 1.09 kg. What is the hp output of the motor?
Problem 2 Six years ago, an 80-kW diesel-electric set cost $160,000. The cost index for this class of equipment six years ago was 187 and is now 194. The plant engineering staff was considering a 120-kW unit of the same general design to power a small isolated plant that would have cost $211,707. Based on the information above the plant engineering staff is considering a 100-kW unit of the same general design to power a small isolated plant. Assume we want to add a pre- compressor, which (when isolated and estimated separately) currently costs $13,000. Determine the total cost of the 100-kW unit.
Find the value of the currents I1 and 12. 100 ohm 5V 5V 100 ohm 12 O a. 1=-0.3A, 12=-0.1A O b. 11=0.3A, 12=0.1A Oc. 11=0.05A, 12=0.1A O d. 11=0.1A, 12=0.2A
What is the indicated horsepower of a single cylinder four-stroke gasoline engine if the engine speed is 1000 rpm? Assuming the mean effective pressure of 0.55 MPa. The diameter and piston stroke is 110mm and 140mm
3. Conservation of energy means that the total input energy is equal to the output energy. Select one: True False
10. The output voltage of a turbine is 224 V at no load and 218 V at full load. How much is the copper loss in the transformer if the current is 1000 A at full load, assuming that the entire copper loss materializes inside the transformer?
What is the power output of a motor that provides a torque of 2,917 N*m while running at 2,641 rpm? Provide your answer in kW and round to the nearest whole number.
Find the total resistance across points A & B. Assume each resistor is 2ohms
A compressor that has been in service for 20 years has finally broken down beyond repair, and now must be replaced. The old 180hp machine cost $1200 and its cost index at that time was 144.5. The new machine will be 400hp. How much will the new machine cost, given that today's compressor index is 252.4 and the power-sizing exponent for compressor sizing is 0.32? A: $929 B: $2706 C: $1434 D: $2096 E: $1549
When the heat gain is less than the heat losses, then Select one: a. We will need a cooling system b. We will need a heating system c. All the mentioned answers are incorrect
Question 5 The blower requires 20 kW to run at 350 rpm. The power is transmitted by a v-belt shown in Figure 4 from an electric motor. The diameter of the machine pulley is 650 mm and that of the motor pulley is 330 mm. The centre distance between the pulleys is 1.2 m. The contact angle of the belt is 150°. The safe pull in each belt is 900 N and the mass of the belt is 0.46 kg per meter length. The coefficient of friction between the belt and the pulley is 0.25. The belt should not exceed the speed of 1 800 m/min. X1 = 16 mm H= 6 mm B X2 = 7 mm Figure 4: Cross sectional view of the v-belt 5.1. Calculate the velocity of the belt in m/s. Determine the length of the belt. Calculate the belt tensions. 5.2. 5.3.