Answered: A single phase motor of 210 V, its…

A single phase motor of 210 V, its circuit shown below, calculate motor slip, forward torque and backward torque. 3.3 N 54° I

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 1 Consider the equations of motion of an armature controlled DC motor given by Jw(t)+bw (t) Ki (t) = di (l) L + Ri (t) + Kw (t) = -Tfriction - Tload (t) Vin (t), dt where vin(t) is the input voltage and Tload(t) is the input load torque. The outputs are the armature current i(t) and the motor speed w(t). When the input voltage and torque are constant, the transient response of this system has the form of the homogeneous solution. What is the time constant of the transient response? Find the characteristic roots of this system first. Keep 3 significant figures, and do not include units. Use scientific notation. The constants are given below: Nominal voltage, Vin(t) = 17 V Moment of inertia of the rotor, J = 0.02 kg-m² Motor viscous friction constant, b = 0.009 N-m-s Friction torque, Tfric = 0.003 N-m Armature inductance, L = 0.1 H Armature resistance, R = 0.35 Back emf constant and motor torque constant, K = 0.21 N-m/A. **Recall that the time constant (or relaxation time) is…
A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.
5:33 PM What is the largest power 10/10 that can be transmitted by the pulley A of a V-belt drive. Illustrated below. Given: n1 = 3000.rpm, r1 = 80 mm, ß =18°, ¤=160°, f = 0.25, F= 1100 N, w = 1.4 N/m. F2 15.7Nm , 4.93 kW 14.6Nm, 5.07kW 13.2Nm, 6.09kW 12.5Nm, 5.34kW Other:
QUESTION 8 Consider the equations of motion of an armature controlled DC motor given by Jw(t)+bw (t) Ki(t) = -Tfriction - Tload (t) di (t) + Ri (t) + Kw (t) = Vin (t), dt where vin(t) is the input voltage and Tload(t) is the input load torque. The outputs are the armature current i(t) and the motor speed w(t). The steady-state response of motors are specified by nominal voltage, stall torque, stall current, no load speed, and no load current. At steady-state operation, the motor equations satisfy bo) -Ki =-T -T. fric load Ri +Kov_- 55 55 The stall torque is the load torque required stead-state speed of the motor is zero. The stall current is the armature current when the motor speed is zero. The no load speed is the speed of motor when the load torque is zero. The no load current is the current when the load torque is zero. What is stall torque for this motor in N-m? Keep 3 significant figures, and do not include units. Use Scientific notation. The constants are given below. Nominal…
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
Given the information for a motor, determine its LCC in term of present worth (in $). Annual discount rate (i.e. interest rate): 10% Life time: 5 years Initial cost: $6500 Energy usage: $500/year Maintenance cost: $400/year Salvage value: $500 A 9601 B 11471 с 11068 D 12170 E 10625
Parameter Value Unit Remarks Inertia 36 tonne m? Damping 20 N-m.s Train mechanisms only Load Torque 117.720 kN-m A train has the effective total properties in the preceding table. It is desired to be able to completely stop the train from full speed in 15 seconds, while maintaining rated supply to the field. 1. Find the number of DC motors needed to run and decelerate the train without any motor being subjected to more than its rated capabilities. Assume uniform load distribution; identical machine models, terminal voltages, and controls. 2. Derive an expression for the armature current la(t) in each machine. 3. Derive an expression for the instantaneous terminal voltage Va(t) required for the controllers. 4. Due to practical limitations, it is often necessary to stop regenerative braking once one of the following occurs: zero-speed, zero Va(t), or zero la(t). Determine the angular speed (in rpm) at which this occurs.
Q3) A 220 V d.c series motor has armature and field resistances of 0.15 Q and 0.10 Q respectively. It takes a current of 30 A from the supply while running at 1000 rpm. If an external resistance of 1 Q is inserted in series with the motor, calculate the new steady state armature current and the speed. Assume the load torque remains constant.
Problem 1 3-Phase AC Machinery Principles Part 1: Complete the following table by calculating the speed of magnetic field rotation in AC machines depending on the number of poles and the operating frequency. Number of Speed (RPM) Poles Frequency f = 50 Hz Frequency f= 60 Hz 4 6. 10 Solution
The nameplate data of a separately excited DC motor is PN=5.5kW, UN=110V, In=80A, n=1000r/min. Try to plot its inherent mechanical properties of this motor.
An unbalanced small motor with me-1.2 kg.m is directly bolted to a machine with a mass of 500 kg. The machine is attached to the floor using an isolator with k=75000 N/m, e=1850 Ns/m (Weight of the motor is neglected.) a) Determine that how much percent of the force is transmitted to the floor if motor turns with n-250 rpm. b) Determine the rotation speed of the motor corresponding to the damped natural frequency of the system. e) Determine the vibration displacement amplitude at the speed calculated in part b).
Q5.A 50 HZ, 4-poles star connected induction motor has a slip=0.04 & Pout=20hp find: (1).Synchronous speed in r.p.m.(ns) 2)rotor speed in r.p.m(n;) 3). Rotor frequency (f:). 4Loud torque, 5) Rotor frequency Note: 1hp=746watt