In a balanced three-phase system, the Y-connected source has an abc sequence andVan = 100235 (rms). The source feeds two loads, both of which are Y-connected.The impedance of load 1 is 10 + j8N/0. The complex power for the a-phase ofload 2 is 450218° VA.%3DFind the total average power supplied by the source.Lütfen birini seçin:a.4235b.2498c.3113d.4879e.3654

Given balanced three phase system Star connected source phase voltage The impedance of the load-1…

In a balanced three-phase system, the Y-connected source has an abc sequence and 100435 (rms). The source feeds two loads, both of which are Y-connected. Van The impedance of load 1 is 10 + j8N/p. The complex power for the a-phase of load 2 is 450218° VA. Find the total average power supplied by the source. Lütfen birini seçin: a.4235 b.2498 c.3113 d.4879 e.3654

In a balanced three-phase system, the Y-connected source has an abc sequence and 100435 (rms). The source feeds two loads, both of which are Y-connected. Van The impedance of load 1 is 10 + j8N/p. The complex power for the a-phase of load 2 is 450218° VA. Find the total average power supplied by the source. Lütfen birini seçin: a.4235 b.2498 c.3113 d.4879 e.3654

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Similar questions

Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
The following loads are served by a balanced three-phase source: Load 1: 18 kVA at 0.8 pf lagging Load 2: 8 kVA at 0.8 pf leading Load 3: 12 kVA at 0.75 pf lagging. Give the complex power expression for Load 3. Select one: O a. 29.80 +j13.94 O b. O c. 9.00+ j7.94 kVA 6.40 -j4.80 KVA O d. 32.90225.07° KVA O e. 14.40 +j10.80 kVA
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
There is an installation with two equal three-phase loads of 150 kW each and a power factor of 0.9 in lagging. By connecting a pure reactive element in parallel, the reactive power at the input of the installation is 160 kVARS, with a lagging power factor. It can be said that:A)Capacitors were connected and the fp improved. B) Capacitors were connected and the fp improved. C) Reactors were connected and the fp improved. D)Reactors were connected and fp improved. E) None of the above
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
Three Impedances each of (9 - j18)N are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
There is an installation with two equal triphasic loads of 300 kVA each and a power factor of 0.9 lagging. When connecting a pure reactive element in parallel, the reactive power at the entrance of the installation is 150 kVARS, with a lagging power factor. We can say that: a) A bank of reactors was connected and the fp deteriorated. b) A capacitor bank was connected and the pf deteriorated. c) A bank of reactors was connected and the fp improved. d) A capacitor bank was connected and the pf improved. e) None of the above
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: Give the value of reactive power per phase seen at load 2.
A load of 240 +j 120 is connected to a source of 240 V with a phase angle of 300, through a transmission line with an inductive reactance of 60 ohms. A Capacitor bank of a capacitive reactance of 120 ohms is connected in parallel to the load. The power factor at the load is: O A. 0.447 lagging O B. 0.707 leading O C. 0.447 leading O D. 0.707 lagging O E. None of choices are correct
In an installation there is a three-phase load of 300 kVA with a power factor of 0.8 behind, in parallel with a three-phase load of 150 kVA with a power factor of 0.6 ahead. A pure reactive element is connected in parallel, and a unity power factor is obtained at the power input. Indicate the reactant of the element, with a positive sign if it is a bank of reactors, or with a negative sign if it is a bank of capacitors. Just put the corresponding sign followed by the numerical value, without units. The numerical value must correspond to the three-phase kVARS. You can use integer values with no decimal places or up to two decimal places
In an installation there is a three-phase load of 300 kVA with a power factor of 0.8 behind, in parallel with a three-phase load of 150 kVA with a power factor of 0.6 ahead. A pure reactive element is connected in parallel, and a unity power factor is obtained at the power input. Indicate the reactant of the element, with a positive sign if it is a bank of reactors, or with a negative sign if it is a bank of capacitors. Just put the corresponding sign followed by the numerical value, without units. The numerical value must correspond to the three-phase kVARS. You can use integer values with no decimal places or up to two decimal places