In a balanced three-phase system, the abc-phase- sequence source is wye connected and Va 120/20 V rms. The load consists of two bal- anced wyes with phase impedances of 8 + j2 02 and 12+ 3. If the line impedance is zero, find the line currents and the phase current in each load. With draw time domain and Phase diagram

In a balanced three-phase system, the abc-phase- sequence source is wye connected and Va 120/20 V rms. The load consists of two bal- anced wyes with phase impedances of 8 + j2 02 and 12+ 3. If the line impedance is zero, find the line currents and the phase current in each load. With draw time domain and Phase diagram

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
A 30-0 resistor, a 15-02 inductive reactance, and a 12-02 capacitive reactance are connected in parallel across a 120-V 60-Hz line. Find (a) the phasor branch currents, (b) total current and phase angle, (c) impedance, and (d) power drawn by the circuit.
Topic analyze 3 phase circuits with balanced and unblanced load conditions
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
The 3-phase power equation in terms of phase voltage and phase current is /3VplpCoso 3VplpCoso
The phase b voltage and the phase b current of a balance three-phase system are V = 220 sin (wt + 210°) and I = 10 sin (wt-180°). * A. 5256.44 W B. 5514.38 W C. 5715.76 W D. 6049.22 W
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..