In a 300.rough incline, a 1.25 kg block is initially at rest beside a spring that is compressed by 24 cm as shown in the figure below. The spring has a spring constant of 180 N/m and the coefficient of sliding friction between the incline and the block is 0.23. When the spring is released, (a) how far up the incline (with respect to its initial position) will the block slide before sliding back? (b) What is the speed of the block at the inst it is 0.34 m from its initial position? 30°

In a 300.rough incline, a 1.25 kg block is initially at rest beside a spring that is compressed by 24 cm as shown in the figure below. The spring has a spring constant of 180 N/m and the coefficient of sliding friction between the incline and the block is 0.23. When the spring is released, (a) how far up the incline (with respect to its initial position) will the block slide before sliding back? (b) What is the speed of the block at the inst it is 0.34 m from its initial position? 30°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A body of mass 20 kg slides up on a 300 inclined plane under the action of an applied force 300 N.The coefficient of friction is 0.2. Find acceleration. R=Wsin30 P=300N F= uR W- 20x9.81= 196.2 N 30
A block of mass M1 resting on an inclined plane is connected by a string and pulleys to another block of mass M2 as shown in Fig. Find the tension in the string and acceleration of the blocks. Assume the coefficient of friction between the blocks M1 and the plane to be 0.2. M1=1500N , M2=1000N . Angle of inclined glane = 45 degrees
In a 300-rough incline, a 2.15 kg block is initially at rest beside a spring that is compressed by 42 cm as shown in the figure below. The spring has a spring constant of 180 N/m and the coefficient of sliding friction between the incline and the block is 0.32. When the spring is released, (a) how far up the incline (with respect to its initial position) will the block slide before sliding back? (b) What is the speed of the block at the instant it is 0.43 m from its initial position? wm 300
2.0 kg push 45° Problem 4: (a) The 2 kg wood box in the Figure above on the left slides up a vertical wood wall while you push on it at a 45° angle. The coefficient of kinetic friction for wood on wood is Hk = 0.2. What magnitude force Fpush should you apply to cause the box to slide up at a constant speed? Recall that constant speed means a = 0 m/sec?. Answer: 34.6 N. (b) Let's re-do part (a), but with the box now sliding down the vertical wood wall while you push on it at a 45° angle. Hk is still Hk = 0.2. What magnitude force Fpush should you apply to cause the box to slide down at a constant speed? Recall that constant speed means a = 0 m/sec?. Answer: 23.1 N. Problem 5: The Figure shows two blocks connected by a cord (of negligible mass) that passes over a frictionless pulley (also of negligible mass). The arrangement is known as Atwood's machine. One block has mass mi = 1.3 kg; the other has mass m2 = 2.8 kg. What are: (a) The magnitude of the blocks' acceleration. Answer: 3.6…
(II) A 25.0-kg box is released on a 27° incline and accelerates down the incline 0.30 m/s2at Find the friction force impeding its motion. What is the coefficient of kinetic friction?
Show the complete solution. Put notes on steps. The wooden block (mass m = 0.6165 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle 0 = 45°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
An object with weight W is dragged along a horizontalplane by a force acting along a rope attached to the object.If the rope makes an angle θ with the plane, then the magnitudeof the force is given below in image. where μ is a constant called the coefficient of friction.(a) Find the rate of change of F with respect to θ .(b) When is this rate of change equal to 0?; (c) If W =50lb and μ =0.6 , draw the graph of F as afunction of θ and use it to locate the value of θ forwhich dF/dθ =0 . Is the value consistent with youranswer to part (b)?
A wooden block(s) of mass M= 400 gram and m = 100 gram is the total mass just starts to move when the hanger mass 200 gram. The tension in the cord is: O a. 2N O b. 0.5N O C. SN O d. 0.2N 400g 100g motion surface with friction 1200g
Q4/ A four wheels drive BMW car accelerating with 6.5 m/s^2 on an inclined pavement with angle of 30° determine the forces under the front and rear wheels. If the coefficient of friction between wheels and road is 1, base wheels 230 cm, the distance between the front wheels and the center of the car's load 110 cm, the level distance from the incline road 35 cm, and mass of the vehicle 1000 kg
There is a box with height 1.2 m, width 0.8 m and mass 50 kg. It contains a very expensive equipment, which cannot be tilted while moving. There is a rope connected to the top-right corner of the box that you can pull with. The static friction coefficient between the floor and the box is 0.4. Assuming the rope angle θ is 30 degrees and m/s2. a) Is it possible to move the box using the rope without tilting the box? (need to show details) b) What is the minimum force required to move the box on the floor?
A 200-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 34.5° with respect to the horizontal. The coefficient of kinetic friction between the log and the ramp is 0.870, and the log has an acceleration of 0.750 m/s2. Find the tension in the rope.