A block of mass M1 resting on an inclined plane is connected by a string and pulleys to another block of mass M2 as shown in Fig. Find the tension in the string and acceleration of the blocks. Assume the coefficient of friction between the blocks M1 and the plane to be 0.2. M1=1500N , M2=1000N . Angle of inclined glane = 45 degrees

Q: The weight of the stationary box is 39.6 kg. The spring has a length of 0.18 m, an unstretched…

A: Given                                      Angle = 20o                                  Mass, m =…

Q: In the figure, two blocks are connected over a pulley. The mass of block A is 11.0 kg and the…

A: According to Coulomb's law of dry friction:- Total frictional force is independent of the magnitude…

Q: Consider the following diagram. m1320 kg and m2= 10 kg. The system is being pulled by an applied…

A:

Q: Determine the acceleration of each weight in the figure, assuming the pulleys to be weightless and…

A: Given data: mA=150 lbmB=480 lbmC=300 lb

Q: A 150 kg table is resting on 60°sloping floor from vertical axis with coefficient of friction u= 0.6…

A:

Q: Consider the following diagram. m1=20 kg and m2= 10 kg. The system is being pulled by an applied…

A: Form above FBDWe havemgsinθ+μsmgsinθ=T110×9.8×sin 30°+0.2×10×9.8×sin 30°=T1T1=58.8 N

Q: 1. A 15 kg box frame is sliding down a 20° incline plane with a 10 kg steel sphere suspended inside…

A:

Q: Two mass m,= 6 kg connect to mass m2=4 kg and both masses with block of mass m;=2.5 kg are attached…

A:

Q: In order to burgle a local McDonald's, the Hamburglar must climb onto the roof. To do this, a ladder…

A: Consider the diagram shown below for the given ladder.

Q: As shown in the figure below, three boxes are placed on an incline. The boxes are initially in…

A: Given data as per the question Mass of block A =20 lb Mass of block B= 40 lb Mass of block C = 30 lb…

Q: A block Rof mass 100 kg is placed on a bloc Sof mass 150 kg as shown in the figure. Bloc R is tied…

A: Given: To determine the minimum force F.

Q: A 6.00 kg block is pressed against a vertical wall by a force. The coefficient of static friction…

A: Given: The mass of the block pressed against a vertical wall is mi=6.00 kg. The coefficient of…

Q: A light, inextensible cord passes over a frictionless pulley as shown in Fig. tached to block B; a…

A: Given data: Coefficient of friction between the blocks = 0.33 Coefficient of friction between block…

Q: A luggage handler pulls a 20.0 kg suitcase up a amp inclined at 32.0° above the horizontal by a…

A:

Q: I A block R of mass 100 kg is placed on a block S of mass 150 kg as shown in the figure. Block R is…

A:

Q: 2. A block of mass m, = 20 kg which lies on an incline frictional surface is connected to another…

A: Answer:                 m1=20 kgm2=100 kgμ=0.12

Q: 120N 60N 60°

A:

Q: When a drawer is pulled by only one of the handles, it tends to twist and rub as shown (highly…

A: Given Data: The coefficient of friction between sides of drawer is: µd1=0.1 The coefficient of…

Q: A steel beam has a weight of 100 kg and is lifted at its left end by a cable passing through a…

A:

Q: A 20-kg block is pulled by a horizontal force F. When the applied force is 30 N the block starts to…

A:

Q: A block R of mass 100 kg is placed on a block Sof mass 150 kg as shown in the figure. Block R is…

A:

Q: A 30-kg box is sitting on an inclined surface as If the coefficient of friction between shown in…

A: A free-body diagram of the box is given as, On using force equilibrium in normal to the inclined…

Q: In the figure above, blocks A and B have 50 and 10 kg respectively. It is given that the…

A:

Q: QI Block A in the figure below weighs 1.40 N, and block B weighs 4.20 N. The coefficient of kinetic…

A:

Q: 1. An S0 kg container box is resting on a wooden support as shown in the figure. The coefficient of…

A: For solution refer below images.

Q: A porter governor its central load is 18 kg and the weight of each ball is 2 kg. The top arms are 25…

A: Given that M= 18 kg , m= 2kg  , BP= 25 cm , BD=30 cm , α= 45° =β;F=14 N , h1= PG= BPcos45= 17.68 cm…

Q: The block M in Fig (a) weighs 500N and has a downward velocity of 5 m/s at the instant the force P-1…

A:

Q: A bicycle and rider travelling at 15 km/hr on a level road, have a mass of 100 kg. The brake is…

A: Write the given information.

Q: A speedboat with a mass of 529 kg (including the driver) is tethered to a fixed buoy by a strong…

A: Given : mass of the speedboat, m = 529 kg length of cable, r = 28.3 m Tension Force in Cable = Fc =…

Q: 4ft 10

A:

Q: A 6-m long ladder has a mass of 16 kg, and its center of gravity is 2.4 m from the bottom along the…

A:

Q: A block R of mass 100 kg is placed on a block Sof mass 150 kg as shown in the figure. Block R is…

A:

Q: The rope connecting the two blocks of Fig. passes over a fixed drum. The coefficient of friction be-…

A: Mass of Right block = m = 100 kg Mass of Left block = M kg Coefficient of friction between right…

Q: A force, F = 12 N, making an angle of 02 = 15° to the ramp pulls up a block of mass m = 2 kg. The…

A: (a) The acceleration of the block up the ramp when the length of the spring is 0.6 m is 0.4 m/s2.…

Q: Q3 Block A moves on a roller along inclined surface and be connected by a rope to black 15.…

A:

Q: A bicycle and rider, travelling at 12 km/h on a level road, have a mass of 105 kg. A brake is…

A:

Q: A 200-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The…

A:

Q: A pile-driver hammer has a mass of 300 kg and is to be raised 16 m in 4 sec. The total friction on…

A: Given data: m=300 kgs=16 mt=4sF=400 N

Q: A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and…

A: Given:-            Belt speed N = 1440 m/min friction coefficient between pulley and belt  The…

Q: A 30° a P. B.

A: Support reaction induce at point C , normal reaction at point B and friction force develop at point…

Q: A 120-lb girl is walking up a 48-lb uniform beam Determine how far up the beam the as shown in Fig.…

A: Given data: The weight of girl, Wg = 120 lb. The weight of beam, Wb = 48 lb. The coefficient of…

Q: Two blocks A and B, of weight 150 N and 200 N, respectively rest on an inclined plane as shown in…

A: Frictional force is defined as the force of resistance offered by the surface which opposes the…

Q: W

A:

Q: Blocks A, B, and C are placed as in Fig. and connected by ropes of negligible mass. Both A and B…

A: The free body diagram for the block A and B is (a) Here T1 is the tension in the rope between block…

Q: A 6-m long ladder has a mass of 13 kg, and its center of gravity is 2.4 m from the bottom along the…

A:

Q: Question Bank - Friction %3D Find the smallest force P that the worker must apply to the bar CD in…

A: Given Data Mass of the spool is: m=80 kg Coefficient of friction at A is: μA=0.12 Coefficient of…

Q: A 6-m long ladder has a mass of 10 kg, and its center of gravity is 2.4 m from the bottom along the…

A:

Q: A body of weight 450 N is pulled up along an inclined plane having inclination 30° to the horizontal…

A: Given: W=450 Nθ= 30°μ=0.25

Q: Two blocks mA = 3.0 kg and mB = 8.0 kg are on inclines and are connected together by a string as…

A: (a) Draw the free body diagram of body A. WA=mAgWA=3 kg9.8 m/s2WA=29.4 N

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.