How long willit take a charged 80 uF capactor to lose 37%% of its initial energy when it is allowed todischarge through a 45 O resistor?a. 3.58 msO b. 1.66 msOc 1.79 msO d. 0.51 msOe. 0.83 msNext pageDageIntroduction to Phys102>Jump to

Answered: Image /qna-images/answer/dfc712f6-c946-4f96-bd58-137b54ef5f9e.jpg

Answered: How long will t take a charged 80 uF…

How long will t take a charged 80 uF capacitor to lose 37% of its initial energy when it is allowed to discharge through a 45 Q resistor? O a. 3.58 ms Ob. 1.66 ms Oc 1.79 ms O d. 0.51 ms Oe. 0.83 ms

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter21: Current And Direct Current Circuits

Section: Chapter Questions

Problem 31P

See similar textbooks

Similar questions

A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
Unreasonable Results (a) What current is needed to transmit 1.00 102 MW of power at 10.0kV? (b) Find the resistance of 1.00 km of wire that would cause a 0.0100% power loss. (c) What is the diameter of a 1.00-km-long copper wire having this resistance? (d) What is unreasonable about these results? (e) Which assumptions are unreasonable, or which premises are inconsistent?
Consider a power plant is located 60 km away from a residential area uses Q-gauge (A=42.40mm2) wire ofcopper to transmit power at a current of I = 100.00 A.How much more power is dissipated in the copper wires than it would be in superconducting wires?
1. At what rate is thermal energy being generated in the 2R-resistor when &= 21 V and R 3.0 o? R. 2R R Select one: a. 13.5 W b. 18.4 W C. 1.5 W d. 6 W e. 24 W OO Shot by Hisense H12
5. A certain Tesla car has a 400 V battery which stores 2.9x108 J. The car can travel 402 km (250 miles) at 105 km/hr (65 mph = 29 m/s) on just the battery before it is depleted. The steps below will let you determine the current delivered by the battery. A. How long does it take to deplete the battery? B. What is the power delivered by the battery (P=E/dt)? C. Power in a circuit is related to the potential difference, current and resistance in the circuit. What is the current delivered by the battery? D. What is the resistance of the circuit?
In the saturation region (I-V characteristics) of JFET the value of D18 ssmemanmnssnes at specific (VGS = * .negative voltage ) a. b.c.d a: constant O b: zero O c: maximum O d: Bothaandc O
A rod of length 2.3 m, with a rectangular cross section (1.5mm x 3.0 mm) is made ofa material with a resistivity of 6.1 × 10^-8 Ohm. A potential difference of 5.0 V isplaces across the ends of the rod.a. Draw a clear physics diagram of the problem.b. At what initial rate is heat generated in the rod?c. Will the rate from part (b) increase, decrease, or remain constantover time, as the rod remains connected to the 2.5 V potential difference?Explain briefly
The following graph represents the charge-discharge profile of a Li-ion battery in the 1st and 50th cycles, cycled at a rate of 0.1 C (1C = 274 mA h g-1 ) in the voltage range of 3.0 to 4.6 V. The battery is made up of LiCoO2 cathode and Li anode. Answer the following questions. a. What is the value of charge-discharge current density in this case? How long does it take for this battery to discharge from 4.6 V to 3.0 V in 50th cycle? b. Calculate Coulombic efficiency at 1st and 50th cycles. Why are these values different? c. How would this graph look like if LiCoO2 and Li were replaced by MnO2 and graphite electrodes respectively Make a rough sketch. d. Mention any two practical disadvantages of this battery?
mid 9634&page 3 A conductor has a cross-sectional area of 2.3x 10 m and the number of free electrons per unit volume is 8.5x 104 electron/m'. When the current is 10.2 A, find the drift speed (in mm/s) of the electrons. Use the charge of the electron to be 1.6x 10 C. Select one: OA. 0.43 OB. 0.33 OC. 32.61 OD. 0.22 OE. 42.81 page Next page 9:03 P A OD A de ENG 4/30/20 nert 17 V Badapace Nom Sok Y 7 GYH K 4. 15 Enter BYN M 1 Shift End Ead
The heater element of a 120V toaster is a nichrome wire with length of 5.4 m, and diameter of .48 mm. The resistivity of nichrome at the operating temperature of the toaster is 1.3x10^-6 ohm-meter. What is the power drawn drawn closest to? A. 380 W B.370 W C. 360W D. 400w E. 410W
A current of 4.5mA flow through a copper wire in area of 20mm2. The current density is O a. 225000A/m O b.225A/m2 444A/m2 C. O d. 2.25 x10-4 A/m² QUESTION 4 Three resistors of 202, 502, ad 1002 can be connected in series or in parallel. What minimum and maximum resistance can you obtain from these? O a. Rmin=1502; Rmax = 0.082 O b. Rmin=1702; Rmax = 12.52 c. Rmax=170Q; Rmin= 12.5Q O d. Rmin=0.082; Rmax = 12.5Q
A rod of 2.0-m length and a square (2.0 mm x 2.0 mm) cross section is made of a material with a resistivity of 6.0 x 10-8 n- m. If a potential difference of 0.50 V is placed across the ends of the rod, at what rate is heat generated in the rod? a. 3.0 W b. 1.3 W c. 5.3 W d. 17 W e. 8.3 W