How can we measure the impurity -1 ?concentration The average thermal velocity of electrons at -2 T=700K equals The temperature coefficient is negative for -3 Si and positive for GaAs. (T/F) Explain the working principle of pnp -4 .transistor showing all necessary figures What is the difference between real and -5 ?ideal diodes

How can we measure the impurity -1 ?concentration The average thermal velocity of electrons at -2 T=700K equals The temperature coefficient is negative for -3 Si and positive for GaAs. (T/F) Explain the working principle of pnp -4 .transistor showing all necessary figures What is the difference between real and -5 ?ideal diodes

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

1- Explain briefly with figure if exist, the Degenerate semiconductors. 2- When a diode is connected in a Reverse Bias condition, the overall result is a small ne current. Why?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
Sketch current I vs, voltage V for the circuits below. The breakdown voltage of the Zener diodes are shown. Assume 0.6V for all diodes (including Zener diodes) in the forward bias region.
Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)
For the circuit shown in Figure, consider Ideal diodes. If Vs = 19sin wt, Vb = 4 V, the minimum value of output voltage is: Vout at of estion Vs Vb Oa. -4 V Ob. -15 V Oc. -19 V Od. 4 V
Q2) Explain the working of zener diode on both forward and reverse bias. From the circuit in the Figure-2, Rs=1KO, Vz=7.2V and RL=3KN. If Vs = 12V. Find out the following DC parameters: a) Is = ?, Current passing through resistor Rs b) IL = ?, Current passing through resistor RL c) Iz = ?, Current passing through Zener Diode d) VL= ?, Output Voltage (Figure-2) Rs 1k Ohm Is Iz RL VL Vs UA723_ZD2 .3k Ohm 12 V
4. If the diode is open in the circuit, the load voltage is? 5. If the resistor is ungrounded in the circuit, the voltage measured with a DMM between the top of the resistor and ground is closest to? 6. The load voltage measures 12 V in the circuit. The trouble may be? 7. Using the third approximation in the circuit, how low must R, be before the diode's bulk resistance must be considered? + Vs RL 1 k2 12 V Figure
In the circuit shown in the figure, diode voltages are given as 0.6V and rD = 100 ohms. When point B is open circuit AIf + 5V is applied to the point of application, drawing the shape of the circuit formed and calculating the currents passing through the resistors.calculate.
Draw the characteristic curve of the standard PN-coupled semiconductor diode.Specify the correct and reverse polarity zones on the curve and draw the appropriate connection shapes.After mark the critical points on this curve and explain what these points mean.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV