Q5: Design a full-wave bridge rectifier with 1k2 load. The rectifier operates from A.C supply of 220v (rms) and 50HZ through 20-to-1 step down transformer. What is the peak value of the rectified output across the load and the fraction of a cycle does each diode conduct? What is the PIV of the used diodes. The diodes can be modeled to have 0.8v voltage drop for any current.

Q5: Design a full-wave bridge rectifier with 1k2 load. The rectifier operates from A.C supply of 220v (rms) and 50HZ through 20-to-1 step down transformer. What is the peak value of the rectified output across the load and the fraction of a cycle does each diode conduct? What is the PIV of the used diodes. The diodes can be modeled to have 0.8v voltage drop for any current.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to t6.1. t1: D...... & D.......2. t2: D...... & D.......3. t3: D...... & D.......4. t4: D...... & D.......5. t5: D...... & D.......6. t6: D...... & D......
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Design a clipper circuit to clip off the portions of an input voltage that fall above 3 V or below -5 V. Assume that diodes having a constant forward drop of 0.7 V are available. Ideal Zener diodes of any breakdown voltage required are available. Dc voltage sources of any value needed are available.
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
A silicon diode has 1 ampere DC of current in biasd mode. What is voltage drop across the diode?
A sinusoidal signal with a maximum value of 12V is applied to the input of the bridge type rectifier circuit. Since silicon diodes with a threshold voltage of 0.7V are used in the circuit, what is the maximum voltage of the signal at the output of the rectifier?