Answered: he aluminium and Steel pipes are…

he aluminium and Steel pipes are fastened to rigid supports at one of their ends and to a rigid plate C at others end derive expression for axial stress in the two pipes

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Related questions

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11633 N force. - 540…

A: P= 11633 N Width of the cross section, b= 60 mm Height of the cross section, h= 180 mm

Q: A steel tube of 300 mm external diameter is to be shrunk on to another steel tube of 90 mm internal…

A: Given data: External diameter, d3 = 300 mm, r3 = 150 mm Internal diameter, d1 = 90 mm, r1 = 45 mm…

Q: A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers.…

Q: Find the stresses at point C. -1.5 m 2.5 m 250 mm 125 mm 1.5 m 50 kN/m 50 mm 2 m 4m

A: Find the stresses at point C.

Q: A thin hollow spherical container has a diameter 1 m and a thickness of 4 mm is subjected to an…

Q: Cal culate the stress between the two rods at the weld if the weld has a radius of 0.5 inch and the…

A: Data given- For part a) Small rod Area = 1.0''× 1.5" Tensile load = 50 kips Radius (r) = 0.5 inch…

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Given data: - The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…

Q: pipe wrench Pipe (eylinder)

A: In this problem 2 forces exerted on shaft. Due to the force P bending stress will occur in shaft…

Q: .For the pressure cylinder shown in fig. 6. determine the radial and tangential stresses for…

A: Given data: Outer and inner diameters of pressure cylinder are: Do=200 mm , Di=120 mm. Internal…

Q: A water tank 8 m in diameter and 12 m high has an internal pressure of 117.72 kPa. Determine the…

Q: Pulleys 1 and 2 of the rope and pulley system are connected and rotate as a unit. The radii of…

A: Given r1=0.1 m and r2=0.3 m d=0.015m m=225 kg Assuming no friction between any of the ropes and…

Q: circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force…

Q: 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid…

A: The tangential stress in the tube is 5.20 MPa.

Q: The member consists of the steel rod AB that is screwed into the end of the bronze rod Find the…

Q: Engineer firms in many situations must verify the reliability of existing purchased designs. Your…

Q: A cast ALuminum cy linder o f Purtable hydraulic a riveter is 208 mm in diameter The Pressure 16,8…

A: The above questioni is based on cylinder analysis.

Q: An unpressurized pipe with an outside diameter of 219 mm and a wall thickness of 8 mm is subjected…

A: (a) To find: The moment about x- axis. Given: The load in x direction is Px=14 kN. The load in y…

Q: At the ambient temperature, the A-36 steel pipe fits snugly between the two fuel tanks. When fuel…

A: Given: The change in length, δL = 4.6 mm The modulus of elasticity, E = 200 Gpa The length of pipe,…

Q: Calculate the normal stresses (in Pa) at point A of the bracket caused by the 11023 N force. E4.png…

Q: What, if any, are the stresses at point O? NOTE THAT WE ARE NOW ASKING ABOUT POINT O. Choose all…

A: When a bar is subjected to various loads then there are different types of stresses developed in the…

Q: he bent pipe has a 1.5-in. outer diameter and a 0.2-in. wall thickness. Calculate the largest shear…

A: Let us draw the Free body diagram

Q: An aluminum wire 3.0 m in length and 4.0 mm in diameter supports a 1000 N mass. Determine the…

A: Write the expression of the cross-sectional area of the wire.

Q: 14 mm diameter rivet joins the plates that are each 1.10 m wide. The allowable stresses are 120 000…

Q: The assembly consists of a bronze tube (length = 1200 mm) and a threaded steel bolt. The pitch of…

A: Given: tube→BronzeBrBolt→SteelStcross sectional areas: ABr=1350 mm2ASt=675 mm2Initial…

Q: 3. A cylindrical vessel has the following specifications: Internal diameter = 800 mm Internal length…

Q: View Policies Current Attempt in Progress A typical stainless steel cylindrical vessel is shown. The…

A: Given data D = 48 in t = 0.75 in P = 1.1 ksi Find Hoop stress = ?

Q: three rivets of 25 mm diameter joins the plates that are each 130 mm wide The shearsress in the…

A: The given data are: d=25 mm=0.025 mb=130 mm=0.13 mτr=80 MPa=80×106 Paτb=120 MPa=120×106 Pa Here, d,…

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

Q: The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a…

A: (a) To find: The axial force F in the ring in terms of p, w and r; Calculation: Consider a FBD by…

Q: A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The…

Q: 4.0 kPa is used to carry a 3.5 m3of water has a height of 2.0 m and thickness of 5.0 mm. Determine…

A: given:V=3.5m3h=2mt=5mmP=114KPa

Q: The cylindrical portion of the propane tank has an outer diameter of 12.02 in. and a wall thickness…

Q: In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress…

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: Given data diameter of shaft (d) = 80 mm maximum shear stress in shaft (τmax) = 63 MPa width of…

Q: How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC…

A: Using method of section problem is solved step by step below.

Q: A gear made of aluminum (modulus of elasticity = 69,000 MPa) is press fitted onto an aluminum shaft.…

Q: 11. A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375…

Q: Problem 4 The resulting stress distribution along section AB for the bar is shown. From this…

Q: A pressure vessel containing gas at 250 psi has an outer diameter of 12 inches and a thickness of…

Q: Engineer firms in many situations must verify the reliability of existing purchased designs. Your…

Q: The small steel plate is connected to the right angle bracket by a 10 mm diameter bolt (Figure…

Q: A thick-walled tube with the outer and inner diameter of 360 and 180 mm, respectively is subjected…

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 750kPa. If the allowable…

Q: (a) Summarize the stresses as they act on an element on the top surface of the pipe at point H with…

A: GIVEN:- outer diameter: do=115mminner diameter: di=105mmthe dimensions of pipe: a=510mm,…

Q: A spherical gas tank has an inner radius of r = 1.5m, if it subjected to an internal pressure of p =…

A: r=1.5m Ap=300kPa

Q: PROBLEM NO. 3. Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear…

Q: The AB part of the rod is steel and is 100mm in diameter.The BC part of the rod is copper and its…

A: Given Data Diameter of steel rod is :ds=100 mm Diameter of copper rod is : dc=80 mm Length of steel…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The aluminium and Steel pipes are fastened to rigid supports at one of their ends and to a rigid plate C at others end derive expression for axial stress in the two pipes

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A wood-stave pipe is bound by steel rods which take the untire bursting stress. Find the proper spacing for 8-mm diameter steel rod for a 1.80-m diameter wood stave pipe if the working stress is 60 mpa for a head of water of 20m.
A. It is the torsional parameter equal to twice the product of the area enclosed by the centerline of the tube and the shear flow Choices: Angle of twist Torque Modulus of rigidity Torsional stress B. The first moment of area, Q is maximum at: Choices: Minimum “b” Neither of the choices Both maximum and minimum “b” Maximum “b” C. The statement “Flexural shear stress is maximum at the neutral axis” Choices: Is always true Depends on the value of Q Is not possible Is sometimes true D. It is the boundary condition for a fixed support Choices Y=0 Either of the choices Both choices Y’=0 E. It is the measure of resistance to shear deformation Choices: Modulus of Elasticity Modulus of Toughness Modulus of Rigidity Modulus of Resilience note: please help me in this word meaning sample problems thank you
A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 25 mm diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 90 MPa of which 50 MPa is the initial stress? What circumferential stress is developed in the pipe?
Problem 2: (M2) Design engineers in many situations must justify their selection of material. Your role in a mechanical design company that manufactures steel pipes is to confirm the maximum stresses imposed by a 250 psi oil pressure on the pipe wall, which acts as a pressurized cylinder once the gate valve is closed. If the pipe diameter is 1 foot and its wall is 0.25 inches thick. Evaluate the longitudinal and hoop stresses at point A. Valve A oil in Figure.3: Steel oil pipe
6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 10 mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS ? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY, AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECE SSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INITIAL STRESS?
A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 40-mm-diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 105 MPa, of which 55 MPa is the initial stress? What circumferential stress is developed in the pipe? Why is it necessary to tighten the bolt initially, and what will happen if the steam pressure should cause the stress in the bolts to be twice the value of the initial stress? *
Calculate the stress in the circumferential section of boiler steam drum 2.15 m in diameter and 45 mm thick, when the working pressure is 30 x 105 Pa
A steel tube of 200 mm external diameter is to be shrunkonto another steel tube of 60 mm internal diameter.The diameter at the junction after shrinking is 120 mmbefore shrinking on, the difference of diameters at the junctionis 0.08 mm. Calculate the radial pressure at the junctionand the Hoop stresses developed in the two tubes aftershrinking on.Take E = 2 x 10³ N/mm²
A cast Aluminum crlinder o f a Portable hodrawlic 208 Mm in diameter The 16,8 N/mm2 by gauge riveter is Pressure. of The fluid is Determine Sui table thicknesS of the inder wall assuming that the Yield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial streses middle radius and at the inner outer surface.
Define the main difference between thick and thin cylinders and give an example for each type of cylinder Derive the expression of longitudinal stress, o, for a closed thick cylinder which has inner radius, R₁ and outer radius, R₂ and subjected to internal pressure only. Figure Q3 shows a cross section of composite cylinder that is made by shrinking a tube of 330 mm internal diameter and 50 mm thick over another tube of 330 mm external diameter and 50 mm thick. The radial pressure at the common surface, after shrinking is 180 MPa. Suppose the compound cylinder is subjected to an internal fluid pressure of 1200 MPa, determine; i) the hoop stresses at inner radius and outer radius of inner cylinder, ii) the hoop stresses at inner radius and outer radius of outer cylinder. Ro P Figure Q3 R₁