H.W 1: Determine the memory location addressed by the following 8086 register combinations: (a) CS = 1000H and IP 2000H (b) DS = 2000H and SI = 1002H %3D %3D %3D
Q: Q2: Write down CX in hex (4M), CF (IM) after executing each instruction MOV CX, -SF7H SHL CX.I ADC…
A: The code is of the assembly language. The value of CX and CF after each instruction is as below:
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: The handwritten solution is given in the step-2.
Q: Q1) If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] +…
A: Given Values are:- BX= 1000, DS= 0200, SS=0100, CS=0300, AL=EDH The instruction is MOV [BX]+1234H,…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: your answer is given below:
Q: Q5/ design an interfacing circuit for the memory to meet the following specification: 1-…
A: Answer:)
Q: Compute the binary representation of the following mips instruction: a) addi $s3, $t3, 7…
A: instruction: addi $s3, $t3, 7 Binary : 00100001011100110000000000000111
Q: Two similar processors A & B with F of 4 &S GHz and CPI of 0.2 & 0.3 respectively. Assume that the…
A: Dear Student, Here No of cycles in 1 second in A = 4GHz = 4 x 109 cycles per second. CPI of A(Cycles…
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given: We are given various registers with values stored in them. Register such as SS, DS, ES, CS,…
Q: Find the Addressing mode: Physical Address/es: Content of the destination:
A: Answers In the given instruction destination is EDX register and source data is the contents of…
Q: in 8086 Identify the addressing modes used for the source and destination operands, and then compute…
A: The answer to the question is given below:
Q: 6. A segment register =- for a physical address= 60000H and offset=D470H. 7. If an 8086 logical…
A: 6) Solution) 52B90H Explanation: Since Physical Address = Base Address + Offset Hence, the value of…
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: MOV 20.[DI], AL Here we are given that DS = 6000H Shifting left 20 times we will get 6000…
Q: Explain (in one to two lines) the function of the instruction MOV [BX], 2587H, if BX =2000H and DS…
A: The MOV instruction copies a byte or a word from source to destination. Both operands should be of…
Q: Q2) If BP=3000H, SI= 0022H, DS= 0200H. SS=0500H, BX=3471H, and CX=AB28H. Explain and draw the type…
A: BP = 3000HSI = 0022HDS = 0200HSS = 0500HBX = 3471HCX = AB28H Need to define type of addressing mode…
Q: 3) Assume SS=5000H, DS=600OH, ES=7000H, CS=9000H, BX=1000H, DI=2000H, SP=3000H, IP=4000H, SI=2000H,…
A: Given Instruction: MOV [DI + 3000H], AL. -> Here MOV means Move instruction. The content of…
Q: "uppose we have the instruction Load 500. Given that memory and register R1 contain the values…
A: Instruction Load is 500 So, Assuming R1 is implied in the indexed addressing mode. Immediate…
Q: XOR AL,[BP+DI] Select one: a. Register addressing mode b. OC. Indirect addressing mode d. Base plus…
A: The way of specifying the data that are to be operated by an instruction is known as addressing…
Q: he 64K single memory chip is used in total. Determine the number of lines in address bus including…
A: option(f) is the correct option.
Q: Suppose we have the instruction Load 500. Given that memory and register R1 con tain the values…
A: In immediate addressing mode, the value present is the operand itself. So here A = 500 In direct…
Q: Note: Identical answers are neglected Q1: Identify the addressing mode for the following…
A: INTRODUCTION : The physical address is a memory address translated to a binary number by the address…
Q: Ques. if the number of general purpose registers (e.g. $t0, $a0, etc.) was increased to 64, then the…
A: The answer is True.
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given Instruction: MOV [DI + 3000H], AL. -> Here MOV means Move instruction. The content of…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: Here, I have to find addressing mode, physical address and content of the destination.
Q: Column X 1. MOV A, #25H 2. MOV R6, A 3. MOV 56H, A 4. MOV @RO, A 5. MOVC A, @A+DPTR Column Y A.…
A:
Q: 3) Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=100OH, DI=2000H, BP=3000H, IP=4000H, SI=2000H,…
A: Finding the physical address MOV 30.[SI], AL Here we are given that DS = 6000H Shifting left 20…
Q: Problem 4: Give a block diagram for a 8M x 32 memory using 512K x 8 memory
A:
Q: H\W: Assuming the SP-1236. Ax-2486. DI= 85c2 and Dx-5f93, show the content of the stack and the…
A: Given Data: SP = 1236H AX = 2486H DI = 85C2H DX = 5F93H ADD AX,SP: Add values of AX and SP and…
Q: What MIPS instruction format(field) is used for the following: -Addi $s3,$s3,4 -Sub…
A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: The answer as follows
Q: Computer Science Write down the register transfer notation for the following assembly language code…
A: Answer: I have given answered in the handwritten format
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: given, the contents of the register SI=AECDH. convert, AECDH from hexadecimal to decimal. 160 * 13 +…
Q: 2. Identify the addressing mode for the following: a. add $8, $9, $10 b. addi $8, $9, 100 C. lw $8,…
A: Addressing mode is expression which is used for addressing mode in the way that the operand of an…
Q: 9. Write instruction sequence to add Ox0A to Ox222 - 0X22A by a. Direct addressing mode b. Indirect…
A: Below i have given instruction for both the meathod:
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: Given The answer is given below.
Q: 3) Write a ALP for 8086 to exchange the content of AL and AH registers without using XCHG…
A: We can utilize BL register to trade the worth of AL and AH registers , the code for the equivalent…
Q: Identify if possible the type of addressing modes for the following instructions. 1. MOV BX, [DI +…
A: The different modes for specifying the operand address in the instructions it is referred as…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: your answer is given below:
Q: 2. Suppose that DS = 1300H, SS = 1400H, BP = 1500H, and SI = 0100H. Identify the addressing modes…
A: Solution (a) MOV EAX,[BP+200H] (b) MOV AL,[BP+SI-200H]
Q: a) For the following fragment of 8086 program, show the content of register AX after each…
A: contentent of AX register is AX=AH+AL
Q: Determine the memory location addressed by the following real mode 80286 register combinations: Show…
A:
Q: .MOV R5 #1FH ii).MOV @R1 A iii) MOV R1,05 iv) MOVCA,A+DPTR V) MOV R2 A
A: Function of MOV is to move memory it takes operands 1,2 (i) MOV R5 #1FH : Load 1FH into R5 Now…
Q: B2.JPG MOV SP,[BP+DI+ACBAH] ВJPG PHY. ADD| С6079H АСH C607AH BDH С607вн | СЕН C607CH| F1H C607DH 02H…
A: We need to find required addresses for given assembly code.
Q: Write the MIPS code of the below given C code. Also identify type of each instruction and encode all…
A: Given C code : A[3] = 7*X+9*Y+100;X = 12*A[A[2]]+21*Y-30;Y = A[X]+A[X+2];
Q: b) Given that the crystal frequency of 8051 Microcontroller is 11.059 megahertz, and one machine…
A: crystal frequency is 11.059 MHZ
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given: We are given various registers with values stored in them. Register such as SS, DS, ES, CS,…
Q: Assume the following are given CS=9345H, DS=2835H, SS=9326H, ES=1955H, IP=2233H, BX=C235H, SI=3D32H,…
A: Actually, given information is: CS=9345H, DS=2835H, SS=9326H, ES=1955H, IP=2233H, BX=C235H,…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: Addressing mode , of physical address and content of destination: MOV[BX],BX copy BX contents to…
Q: 3) Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H,…
A: Concept Given: We are given various registers with values stored in them. Register such as SS, DS,…
Q: Q1) If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] +…
A: Given, BX =1000 DS =0200 SS =0100 CS =0300 AL =EDH Instruction = MOV [BX]+1234H,AL Physical…
Q: If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] + 1234H,…
A: Answer: It is a base addressing mode. Effective address of the operand obtained by adding direct or…
![Q: B2.JPG MOV SP,[BP+DI+ACBAH] ВJPG PHY. ADD| С6079H АСH C607AH BDH С607вн | СЕН C607CH| F1H C607DH 02H…A: We need to find required addresses for given assembly code.](/questions-and-answers/b2.jpg-mov-spbpdiacbah-vjpg-phy.-addor-s6079h-ash-c607ah-bdh-s607vn-or-sen-c607chor-f1h-c607dh-02h-c/d2194d0d-d943-4cd8-84e9-b380c338f2bd){kind=link}
Step by step
Solved in 2 steps
- a. Find the address accessed by each of the following instructions. If DS = 0100H, BX= 0120H, DATA = 0140H, and SI = 0050H and real mode operation:1. MOV DATA[SI], ECX2. MOV BL, [ BX+SI]b. Descriptor contains a base address of 00260000H, a limit of 00110H, and G = 1,determine starting and ending locations are addressed by the descriptor for aCore2.The 8-bit register AR, BR, CR, and DR initially have the following values: [5]AR = 11010010; BR = 11111111; CR = 10101001; DR = 10101010Determine the 8-bit values in each register after the execution of the following sequence ofmicrooperations.AR AR + BR Add BR + ARCR CR AND DR, BR BR + 1 AND DR to CR, Increment BRAR AR - CR Subtract CR from ARIn max mode, control bus signal SO,S1 and S2 are sent out in 1 point form * Shared Decoded Unshared Encoded The clock rate of microprocessor 8086 is 1 point FFFF0H 00000H FFFFFH 0000FH To design a 8086 memory system consisting of 1 Mbytes must we have * 1 point 32 number of 64K× 8 memory. 64 number of 64K× 8 memory. 64 number of 32K× 8 memory. 32 mumber of 32K× 8 memory.
- Match segment and offsetregisters and determine their correspondingactual memory location addressed of the following real mode 80286 segment registers given below. Segment Register Effective Address 1. CS = 2010H 2. DS = 2100OH 3. ES = AB80H 4. SS = 1234H 5. DS = B20FH When: a. DI = 2000H d. IP = ABCDH b. BX = 100AH e. BP = 12FFH c. SP = 3A00H Type the address in uppercase. Do not forget to append H to each addresses. 1. EA: 2. EA: 3. EA: 4. EA:The 8-bit register AR, BR, CR, and DR initially have the following values: [5]AR = 11010110; BR = 11100111; CR = 10110001; DR = 10111010Determine the 8-bit values in each register after the execution of the following sequence of microoperations.AR AR + BR Add BR + ARCR CR AND DR, BR BR + 1 AND DR to CR, Increment BRAR AR - CR Subtract CR from ARis stored in the memory starting 2- The ISR address of interrupt number at address (0039CH). 3- In the instruction: (MOV AL,[3AFH]), data is transferred to 8086Mp over data clock cycles. lines: using 4- In the instruction: (MOVAX,[5BC2H]), data is transferred to 8086Mp over data lines: clock cycles. using
- 02:- (A) Find the phicycal address if (BP) = 0100H, (SI) = 0200H , (SS) = 2000H and a displacement of 10H, of the instruction MOV AL. (BP+S+10H]. Which the name of Addressing Modes? 02:- (B) Find the result of the following: 1111-iIH+110010111011B 03: Write a piece of code to find the number of negative integers in an array of size 1024 bytes contain signed numbers stored at addresses starting at 21000H, store the result in a location 51000H12. In a BSL instruction block B3:10 holds the word 8ECOH, and the bit starting address is B3:0/15. What word is held in the B3:10 after one low-to-high transition signals are sent to this BSL instruction block's input?Q2- Write a program in assembly language for the 8085 microprocessor to receive one byte of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When receive the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception(start bits 1 1 ), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit 0 ). The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
- In the following indexed addressing mode instruction, MOV 5(R1), LOC the effective address is А. EA = [R1] EA = 5+R1 C. EA = 5+[R1] D. EA= R1 B.The 8-bit register AR, BR, CR, and DR initially have the following values:AR = 11010010; BR = 11111111; CR = 10101001; DR = 10101010Determine the 8-bit values in each register after the execution of the following sequence ofmicrooperations.AR <- AR + BR Add BR + ARCR <- CR AND DR, BR <- BR + 1 AND DR to CR, Increment BRAR <- AR - CR Subtract CR from AR5. If the state of 8086 is as follows : (SI) = 0500 H (DS: 0500 H) = 00 H (DS: 0501 H) = 10 H Execute the each instruction below: a) JMP 10 H b) JMP 1000 H