For the given state of stress, determine the normal and shearing stresses exerted on the oblique face of the shaded triangular elementshown. Use a method of analysis based on the equilibrium of that element. Take X= 45 MPa.X40 MPa50°The normal stress exerted on the oblique face of the shaded triangular element is -MPa.The shear stress exerted on the oblique face of the shaded triangular element isMPa.

Answered: Image /qna-images/answer/d1869ae3-47b5-4382-8e97-793f9f89c959.jpg

For the given state of stress, determine the normal and shearing stresses exerted on the oblique face of the shaded triangular element shown. Use a method of analysis based on the equilibrium of that element. Take X= 45 MPa. 40 MPa 50° The normal stress exerted on the oblique face of the shaded triangular element is - MPa. The shear stress exerted on the oblique face of the shaded triangular element is MPa.

For the given state of stress, determine the normal and shearing stresses exerted on the oblique face of the shaded triangular element shown. Use a method of analysis based on the equilibrium of that element. Take X= 45 MPa. 40 MPa 50° The normal stress exerted on the oblique face of the shaded triangular element is - MPa. The shear stress exerted on the oblique face of the shaded triangular element is MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A body is subjected to multiple applied loads. The resultant stress at point location (0, 1, 4) meters can be described as or = -5 MPa. Which of the following describes t stress state at this point? Biaxial tension Uniaxial compression Pure shear Uníaxial tension
The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is horizontal and the rods are stress-free. Determine the stress in each rod if the temperature of the rod at A is decreased by 40° C. Neglect the weight of bar ABC. Use a 11.7 x 10-6/°C and E 200 GPa for steel. A = 1200 mm. A 300 mm² 1.2 m 0.9 m C A. 0.6 m- 1.2 m
Calculate the combined stress (MPa) on the rod shown below using the principle stress method. Here, F1 = 0.35 kN, F2 = 0.12 kN, T = 428000 N-mm. Length and diameter of the rod are 75 cm and 75 mm, respectively. F2 F1 d
A piston-cylinder has a force F₁ applied to it. The circumferential stress in the cylinder cannot exceed Omax = 6 MPa. Hint: 1. Pressure = F Area P = F₁ F₁- OG Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value T'inner 44 mm t 1.25 mm r1 a. Determine the max pressure that the piston-cylinder can withstand, P. b. Determine the magnitude of max force that can be exerted on the piston to not exceed omax, F1. kPa N
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of Sx = 210 MPa, Sxy = 150 MPa. Sxy Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
200 mm diameter rod is subjected to loads as shown. Determine the state of stress at points A and B. Show your results on an infinitesimally small square plane (please use the ones drawn below, which helps you in directions). 8 m 600 N 10 m 400 N 700 N + Oz Tyz + Txy Ox Oy A
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm
3. Determine the stress and strain in the cable on the upper beam if the force applied caused point D to move 0.00508 m downwards. Neglect the weight of the bars and the elongation of the cable between the bars. Assume the length of the upper cable is 1 m and the area is 3.2258 x 10³ m. D 2m 12 000 N 2m
1. Determine the normal stress at bar AC. Use diameter of bar AC = 215 mm. 500 N 2 m B 2 m 451
The state of stress at a point in a member is shown on the element. Take σx = 90 MPa , σy= 65 MPa , τxy = 40 MPa . A) Determine the normal stress component acting on the inclined plane AB. Solve the problem using the method of equilibrium. B)Determine the shear stress component acting on the inclined plane AB. Solve the problem using the method of equilibrium.
A state of stress at a point A is given by σx = -75 MPa, σy = 122 MPa, and τxy = -3.75 MPa. Which of the following is one of the principal stresses for the point A.
A point on a thin plate is subjected to the two stress components as shown in Figure 7. Determine the resultant state of stress represented on the element oriented as shown on the right. “L.. 100 MPa Oy 160 MPa Txy |45° Ox + 30 100 MPa