The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes atthe point are S, = 20 MPa, S, = 24 MPa, and Sy = 29 MPa. Assume ß = tan= 21.8°, a = 5, and b = 2. Using the equilibriumequation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and z (magnitude only) atthis point on the inclined plane shown.Answers:iMPa, T =iMPа.

Permissible stress is stress which produces due to pressure or forces which does not exceed the…

The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at = 21.8°, a = 5, and b = 2. Using the equilibrium the point are S, = 20 MPa, S, = 24 MPa, and Sy = 29 MPa. Assume ß = tan¬1 equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and 7 (magnitude only) at this point on the inclined plane shown. Sy Answers: MPa. MPa, 7 =

The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at = 21.8°, a = 5, and b = 2. Using the equilibrium the point are S, = 20 MPa, S, = 24 MPa, and Sy = 29 MPa. Assume ß = tan¬1 equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and 7 (magnitude only) at this point on the inclined plane shown. Sy Answers: MPa. MPa, 7 =

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.18P: -18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see...

See similar textbooks

Similar questions

At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,,sy., andtxy(see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an elastic material. Using Mohr’s circle of stress determine the principal stresses at the point and their directions for each combination. 1}sigmax -60 n/mm2 , sigmay -36n/mm2 ,TAUxy=5n/mm2 2}}sigmax 30 n/mm2 , sigmay -50n/mm2, TAUxy= 30n/mm2
A piston-cylinder has a force F₁ applied to it. The circumferential stress in the cylinder cannot exceed Omax = 6 MPa. Hint: 1. Pressure = F Area P = F₁ F₁- OG Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value T'inner 44 mm t 1.25 mm r1 a. Determine the max pressure that the piston-cylinder can withstand, P. b. Determine the magnitude of max force that can be exerted on the piston to not exceed omax, F1. kPa N