For a combinational logic circuit of four bits Binary Coded Decimal (BCD) inputs and one output having following conditions: • if the equivalent decimal number of the BCD is even then output is 0 if the equivalent decimal number of the BCD is odd then output is 1 Q20. i) Draw the truth table ii) Find the simplified logic function using K-Map iii) Draw the logic diagram

For a combinational logic circuit of four bits Binary Coded Decimal (BCD) inputs and one output having following conditions: • if the equivalent decimal number of the BCD is even then output is 0 if the equivalent decimal number of the BCD is odd then output is 1 Q20. i) Draw the truth table ii) Find the simplified logic function using K-Map iii) Draw the logic diagram

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Select a suitable example for for combinational logic circuit. O a. None of the given choices O b. De-multiplexer O c. PLA O d. Latches
Basic Combinational Logic Circuits 2. Write the output expression for logic circuit: A B B X
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
For a combinational logic circuit of four bits Binary Coded Decimal (BCD) inputs and one output having following conditions: • if the equivalent decimal number of the BCD is even then output is 0 • if the equivalent decimal number of the BCD is odd then output is 1 Draw the truth table 20. i) ii) Find the simplified logic function using K-Map ii) Draw the logic diagram
Design a combinational circuit with 3-inputs and 1-output. The output is equal to logic-1 when the binary value of the input is less than 3. And the output is logic-0 otherwise.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
Q1. Design a 4-input, one output combinational logic circuit for the following input-output conditions: a) If the number of 1’s in inputs is more than or equal to 2 then the output is 1 ?. b) If the number of 1’s in inputs is less than 2 then the output is 0 ?.
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
1. Design a combinational logic circuit with three inputs A, B and C and one output X. When only one input is 1, output is 1. When none of input is 1, output is also 1. Otherwise, output is 0.
(b) Figure Q2(b) shows input waveforms of A, B and C. Draw the logic circuit that will generate the output waveform X. A Inputs B Output X Figure Q2(b) : Input and output waveforms
Task 6: Simplifying Boolean functions in EWB using the logic converter Simplify the following Boolean expression in EWB using the logic converter F (A, B, C) = AB'C'+ A'B'C'+ A'BC'+ A'B'C